Top 10 Best 12v Temperature Controller

100 complete machine patch, wave soldering, stable performance, good consistency.. Embedded CPU chip MCU, more intelligent, lower power consumption.. Automatic power set memory MCU built-in EEPROM memory unit.. Control accuracy of 0.1 degrees Celsius. Have been tested for stability, consistency and reliability.. Tips - long press set to get menu, starts at P0 - press - to get next P-parameter - press set to choose that parameter - press - to select the value you want for that parameter - press set to accept it - long press - reset to default - power-out does reset to default - default temp set is 34.5C.

Simplified Design---Easy to set. Support F display. One Relay Output---Switch between heating mode and refrigeration mode according to the device you plug into the controller. Maximum output load 1100W110V. Safe Protection---High and low temperature alarms are available when the temperature overshoots your desired temperature. Compressor delay protection time setting and Temperature calibration. Warranty---1 year warranty for replacement or full refund without return. Comes with a 3m9.8ft waterproof probe sensor. Measure range is -4 230F.

100 complete machine patch, wave soldering, stable performance, good consistency.. Embedded CPU chip MCU, more intelligent, lower power consumption.. Automatic power set memory MCU built-in EEPROM memory unit.. Control accuracy of 0.1 degrees Celsius. Have been tested for stability, consistency and reliability.. Tips - long press set to get menu, starts at P0 - press - to get next P-parameter - press set to choose that parameter - press - to select the value you want for that parameter - press set to accept it - long press - reset to default - power-out does reset to default - default temp set is 34.5C.

What will receive you will get 2 pieces of direct-current 12V 200 mA temperature controllers, the measurement temperature is from -50 to 110-58 to 230, the control and backlash precision 0.1 Celsius, the refresh rate 0.5 s, the module size 48 x 29 x 32 mm 1.89 x 1.14 x 1.26 inch, the probe length 1.5 inches, the cable probe length 1 ft. Dual color LED display this digital thermostat control module of dual color LED display, which show the measured temperature red and set temperature blue at the same time, which can be applied for cooling heating mode, you can test indoor or outdoor temperature. Waterproof design the NTC 10K 0.5 probe is waterproof, and you can control the temperature at will, can also control heating or cooling according to different needs. Reliable to use the electronic temperature control switch module has been tested for consistency and reliability, and its control accuracy is 0.1 degrees Celsius, backlash precision is 0.1 degrees Celsius with high temperature protection. Wide application the electronic thermostat can be widely applied in intelligent home and industrial equipment, suitable for household appliances, automatic irrigation, office machines, audio, automobiles, aquarium, fish tank etc..

Temperature measuring range-50 to 110 -58 to 230 Resolution 0.1 at -9.9 to99.9, and 1 at other temperature intervalsrefresh rate 0.5 s. Opening size 45mm25mm1.761 Dual color LED displayTemperature controller monitoring instrument, show the measured temperature red and set temperature blue at the same time.which can be applied for cooling heating mode, you can test indoor or outdoor temperature. NTC 10K Which is waterproof, moisture-proof and anti-rust. Available for remote temperate measuring and controlling. It can control heating or cooling according to different needs. The electronic temperature control switch module has been tested for consistency and reliability, and its control accuracy is 0.1 degrees Celsius with 0-110 high temperature protection. The thermostat can be widely applied in intelligent home and industrial equipment, fish tank water temperature control, incubation field, equipment cabinet, air conditioning system, temperature control protection, control cabinet cooling system and other DIY temperature control systems..

W3001 digital LED temperature controller thermostat thermoregulator control devices are equipped with stainless steel probes, hardly rusting, having nice working performance,the ABS material make sure it is not easy to break.. W3001 temperature controller comes with LED display, display the temperature clearly, making it convenient for you to read and adjust the temperature in time.. There are 2 working modes of the digital LED temperature controller module, heating mode start temperature is lower than stop temperature and cooling mode start temperature is higher than stop temperature, range from -50C to 110C The high temperature control accuracy reaches 0.1. W3001 microcomputer digital temperature controller module can be widely applied in the conditioning systems, incubators, equipment cases, temperature control protection and others. Note When setting the heating mode, if you accidentally set the set temperature value upside down, the output indicator will not light up and the load will not work. If the above situation occurs after setting, you can check whether the set temperature value is upside down.

Upgrade Models. Digital display is modified to Fahrenheit temperature display old section is Celsius display. Dual LED display, Red Blue, Precise temperature control, high sensitivity, suitable for any occasion required temperature.. Temperature range-58 to 257 Resolution temperature range -3.9 99.9 is 0.1, other temperature ranges 1 .. Temperature measurement accuracy 1 . Backlash accuracy 0.1 . Refresh rate about 0.5S. Input Power DC 12V.. Measuring input 1 meter NTC 10K 0.5 waterproof metal sensors.. Relay Load DC 14V 20A AC 125V 20A. If the module works for a long time, it is recommended not to exceed 10A.. LM YN Digital Thermostat Module User Manual https1drv.msbsAlzQUCOyZQhKeM8jiVLkOiED33geUs6eMG.

The W1209 thermostat module controller has a sensor input, keys, LED display, and a relay. It can be reprogrammed for control, timing, or counting.. Temperature Measurement Range -50110. Control Precision 0.1 celsius.Input Power DC 12V Measuring Inputs NTC 10K 0.5 Waterproof Sensor 0.5M Output 1 Channel Relay Output, Capacity 10A Power Consumption Static Current 35mA Current 65mA.. Electronic digital thermostat with a 3-digit LED display, extremely bright. Operation both in heating and cooling to easily control equipment and devices.. The output is electronically controlled by a microprocessor, to guarantee the utmost precision of intervention and an excellent resolution of reading temperature.. The NTC probe is waterproof and allows to control the temperature even of fluids, allowing the controlled heated or coolingNote The wood laminate case is the clear plastic case. You need to tear the wood outside layer off carefully, the outside layer is very thin. It can protect the inside to prevent scratches. And you need to assemble and install the case by yourself, it comes disassembled with tiny bolts and nuts...

Output2 Relays, control the temperature by setting the temperature set value and the difference value.. ModeAutomatic switch between cooling and heating modes, Fahrenheit and Celsius display can be choose.. CalibrationTemperature calibrating, refrigerating control output delay protection.. AlarmWhen temperature exceeds the limit or when sensor error it will alarm. It can be used for peltier water cooling device, cooling fan, car's 12v battery, 12 volt chest cooler,heater etc.. Warranty12V temperature controller with 1 years warranty..

This delicate digital display temperature controller can set Celsius mode or Fahrenheit mode.. The ambient and set temperature preciseness is 0.1. It is convenient to install and wiring is simple.. Wide temperature measurement range from -50 to 110 and supports high temperature protection.. Can be installed directly or embedded in industrial control equipment panel, convenient and quick.. Widely used in the hatching area, equipment case, air conditioning system, temperature control protection and other fields..

Temperature controller monitoring instrument, show the measured temperature red and set temperature blue at the same time. Can be used for coolingheating control. Operating Voltage DC12V 200mA. Measurement Range -50 to 110 Celsius -58 to 230 F, the CF button allows you to switch between Celsius and Fahrenheit temperatures. Clear Working State the relay is closed when the light is on, and the relay is disconnected when the light is off. It has high temperature protection.. With a waterproof NTC 10K 0.5 temperature sensor probe, rogrammable heatingcooling mode, delay start, high temperature alarm, CelsiusFahrenheit mode, etc.. Can be used for fish tank water temperature control, incubation field, equipment cabinet, air conditioning system, temperature control protection, control cabinet cooling system and other DIY temperature control systems..