Top 10 Best 30 Amp Esc

Comes Pre-soldered with XT60 Connector and 3.5mm bullet plugs. 5v3A UBEC Very Efficient - ESC can power receiver and servos. LiPo 2 - 4s Cells, NiCdNiMH 5 - 12 Cells, 6.4V - 16.8V. Low Battery Protection, Overheat Protection, Startup Throttle Protection, Signal Loss Protection, and Abnormal Voltage Protection. Programmable - Programming Card or using Transmitter.

Super smooth, accurate and programmable throttle linearity and throttle response.. Over temperature protection ,low voltage cut off protection ,signal loss protection and so on.. Strong BEC output 2A5V continuous and peak to 3A.. Supporting high RPM motors and programmable by programming card and transmitter .. High efficiency with low resistance and low heat MOSFET and CPU.

NOTE 1. Since 2020.07.05, this items was soldered with 3.5mm Female banana connectors, effectively avoid welding problems 2. We have set up the program, the ESC do not need additional program. Input voltage2-4 S BEC 5V 3A Working current 30A 40A Optional on my shop. Universal SimonK Firmware 30A40A ESC Brushless Speed Controller, super simple. Small size combined with light weight for easy installation. 30A40A is optional on my shop. Military standard capacitor of extreme low resistance increases the ability of prevention of unwanted RF noise during flying. Extreme low resistance PCB is helpful for getting a super current endurance capability.. Microprocessor uses separate voltage regulator IC, with good anti-jamming capability..

-Input Voltage 2-3cells lithium battery or 5-9 cells NiCdNIMh battery.. -Compatible with 400-450 helicopters Aircraft or Quad-Rotor Multi RC Helicopter. -Size 45mm L 24mm W 11mm H..

Strong current endurance Steady Input voltage 3S 4S 5S Lipo battery in Continuous current current 30A, max spoort to 40Ain 10s. Supported Protocols Analog Signals - Multishot, One shot 42, Oneshot125, Digital Signals - Dshot 150, 300, 600. Stable firmware BLheli_S 16.5 is designed for superior performance in multirotors, and uses hardware upgradable. Use top quality components Imported Japanese Toshiba MOSFETs and Japanese Murata Ceramic Capacitors.3oz High-TG PCB board significantly reduces electrical heat soak and improves system efficiency. Ultra-Small and Light footprint 2g weight 2614.5mm ESC with the Silicone Signal and Power Wires provides high heat-resistance and more flexibility.

Universal Firmware 30A ESC Brushless Speed Controller, super simple. Small size combined with light weight for easy installation.. Support OneShot 125. High performance MCU. Mini size, lighter in weight. Built-in BEC, high output power, less power loss.. Multiple protection features Outstanding blocking protection, protect equipment and personal safety. Abnormal startup protection, over-heat protection, throttle signal loss protection, low-voltage cut-off, protection etc.. The firmware is specialized for multi-rotor , fast throttle response during flying.Strong self-adaptable firmware, 4 timing options.. Support frequency of throttle signal to 500Hz max , compatible with various kinds of flight control. 500Hz throttle signal is nonstandard signal .

No need to solder,more convenient,30A an instant 45 A, 40A continuous 10 seconds,BEC output 30A, stressed 5 V 3A. 2LIPO 4-5 micro-steering gear 3 LIPO 3-4 micro-steering gear,all the ESCs were completely cool no issues,they do not get overly hot and hold up great.. Compatible with 400-450 helicopters Aircraft or Quad-Rotor Multi RC Helicopter, good for quad-rotor KK multi-copter. Protection, without Signal one second after the shutdown,security started, throttle position does not prohibit started temperature protection, the surface temperature of 110 degrees downtime out of control. Automatic selection 2-3 LIPO were protected voltage is 6 V9V automatically elected NIMH, each protected voltage is 0.8 V.. The use of BEC, MCU separate power supply,and the use of speed control curve, automatically adapt to the accelerator, more suitable for remote control devices..

1.Chips on EFM8BB21.. 2.BLHeli_S is designed for superior performance in multirotors, and uses hardware.. 3.Small size combined with light weight for easy installation.. 4.Support Damped mode, Oneshot125, Oneshot42 and Multshot. 5.Works with 2S to 6S input - Rated at 30A continuous and 35A burs..

A2212 1400kv Brushless Outrunner Motor with connector, 12A60s, fit for Battery 2-3 Li-Poly.. 30A ESC BEC output linear mode 5V, 2A,Number of battery sections 2-3S LiPo. With T plug and 3.5mm banana connectors,effectively avoid welding problems.. SG90 Servo, 4.8V-6V, 0.12 sec 60 deg 4.8 V.. Suitable for RC Glider Quadcopter Helicopter Aircraft Copter Multi-copter.. Package Included 1 X A2212 1400kv Brushless Motor 1 X 30A Brushless ES 2 X SG90 9G Servos 1 Pair 8060 Propellers and other mounting Accessories..

Made of high quality metal and plastic,easy to install,performs well.. The motor is compatible with a variety of brand electrical tuning, motor efficiency more than 75, high precision dynamic balance, widely used in fixed wing, four axis multi rotor aircraft, model aircraft, etc.. 30A ESC has multiple protection functions, safe start, the wrong throttle position is not allowed to start temperature protection, 110 degree surface temperature shutdown out of control protection, no signal after 1 second stop.. Note firmware cannot be flashedit is not open source and fixed.. It includes 1x 2212 1000KV brushless motor, 1 x 30A ESC speed controller..