Top 10 Best Ade Spike

This Optics Mount Plate is designed to connect Optics Red Dot Reflex Sight to Ruger Security 9 Pistol by Replacing the Rear Sight with this Optic Mounting Plate.. Attention This Ruger Security 9 optic plate does NOT fit Ruger SR9 pistol. Ruger SR9 and Ruger Security 9 are completely two different pistols. Torque screw to 15inchlb. For gun glue, we recommend to use loctite treadlocker. This plate fits Vortex ViperVenom, ADE RD3-003,RD3-006, ADE RD3-009,RD3-012and Pro,RD3-015and Pro, RD3-028, RD3-018 Spike, , DocterNoblex Sight C, DocterNoblex sight 2, DocterNoblex sight III,QUICKsight 5.0 VR, Noblex Sight G,Burris Fastfire 2, 3, Delta Optical MiniDot,Delta Optical MiniDot II,Hawke Reflex,Sightmark Mini Shot Pro Spec,Mini Shot M-Spec,Leica Tempus, MAKdot, Vector Optics SCRD-19II Frenzy,Creative XP GlassEagle HD, HEX Dragonfly,CT RAD Pro, Cyelee CALF V2,Vomz Pilad.. Also fits Burris Fastfire 2, Burris Fastfire 3, Delta Optical MiniDot, Delta Optical MiniDot II, Hawke Reflex 125, Sightmark Mini Shot Pro Spec, Sightmark Mini Shot M-Spec, Leica Tempus, MAKdot 125, Vector Optics SCRD-19II Frenzy 1x17x24, Creative XP GlassEagle HD, Riton MPR D2, Riton 3 Tactix MPRD, Swampfox Sentinal, HEX Dragonfly, HEX Wasp, Crimson Trace CT RAD Pro, Cyelee CALF V2, Cyelee CAT PRO, or Vomz Pilad 120.. Comes with several pairs of screws for ADE, Shield, Holosun, Vortex, Burris red dots. The screws should fits most of the listed red dot but not guaranteed for every red dot. If you need the longershorter screw to work properly, we recommend going to a local hardware store such as ACE Hardware to get the right size..

This is a optic mounting plate for Glock that replaces the factory rear sight dovetail of all Non-MOS Glocks from Glock 17 to Glock 43 to glock 100. Does NOT fit Glock with AFTERMARKET slide. Installing this optic plate requires a qualitied Gunsmith. The included Glock plate fit some other Pistols such as Canik TP9SFdoes not fit SFX, COMBAT, SA. This Glock plate also fits Taurus GX4, G3C G3 with factory steel sights does not fit any other Taurus models such as G2G2CG3 without factory steel sightTx22PT111 because those pistols made the rear sight dovetail based on the Glock rear sight dovetail specifications.. This optic dovetail plate made by ADE only fits genuinestandard glock that has a standard factory rear sight. It does NOT for MOSoptics ready glock. It does NOT fit glock with AFTERMARKET slide.. Compatible with RD3-020 Raptor, RD3-023 Valkyrie, RD3-019 Stingray and Trijicon RMRSROScrews provided for Trijicon and ADE. Also compatible with other red dots that shares the similar footprint, but provided screws may NOT work, such as Holosun HS407CHS507CHS508T, Riton X3 Tactix PRD, Trijicon RMRSRO, Swampox KingslayerLibertyJustice red dot sight. We recommend get the right size screws from a local hardware store.. The footprint of this plate is NOT compatible with other footprints. This plate does NOT fit other red dots such as Vortex VenomViper, Doctor, Burris Fastfire, Shield RMSRMSc, Trijicon RMRcc, Deltapoint Pro, Swapfox sentinel, ADE Spike..

Designed for Sig Sauer P365XL with Optic Cut space for keeping the red dot installed for every day carry.. This IWB Optics Ready holster is compatible with red dots such as Shield RMSRMSCRMSWSMS, Sig Saure Romeo Zero, JP Enterprises JPoint, Swampfox Sentinel, ADE RD3-018 SPIKE, Leupold Delta Point Pro, Vector Optics Frenzy-S Red Dots installed.. Thick .08 Kydex material that is strong, durable, and molded specifically for your weapon. Adjustable Retention so you can get the perfect fit. Package includes holster plus hex adjustment tool.. Fully covers trigger and backside of gun, providing safety and protection from sweat. Adjustable Cant From -5 to 20 Degrees This slight adjustment from -5 to 20 degrees will help angle your holster perfectly for ApprndixAIWB, Strong Side, Behind The Hip or Cross Draw. Fits 1.5 Width Belt. Holster Size L x W x H 6.4 x 3.0 x 1.8. No Risk of Pressing Release. AUDIBLE CLICK AND SECURE RETENTION Audible click sound ensures your firearm is safe and secure every time you reholster..

Designed for SW MP Shield with Optic Cut space for keeping the red dot installed for every day carry.. These IWB holsters for pistols are tailor-made and compatible with MP Shield 9mm and Smith and Wesson .40 3.1'' MP Shield M2.0. Inside waistband polymer holsters for concealed carry your handgun.. Please note these holsters are not fit for MP 9mm and EZ or any attachment like laserlight accessories. This holster is for MP Shield, Not for MP or EZ.. Optic Cut Claw This ADE holster accommodates variety of optics, Claw that reduces printing and increases concealment for your holster.. Thick .08 Kydex material that is strong, durable, and molded specifically for your weapon. Adjustable Retention so you can get the perfect fit. Package includes holster plus hex adjustment tool.. Adjustable Cant From -5 to 20 Degrees This slight adjustment from -5 to 20 degrees will help angle your holster perfectly for ApprndixAIWB, Strong Side, Behind The Hip or Cross Draw. Fits 1.5 Width Belt. No Risk of Pressing Release. AUDIBLE CLICK AND SECURE RETENTION Audible click sound ensures your firearm is safe and secure every time you reholster.. This Right Hand IWB Optics Ready holster WITH CLAW is compatible with red dots such as Shield RMSRMSCRMSWSMS, Sig Saure Romeo Zero, JP Enterprises JPoint, Swampfox Sentinel, ADE RD3-018 SPIKE, Leupold Delta Point Pro, Vortex VenomViper, Trijicon RMRSRO, Deltapoint Pro, Vector Optics Frenzy-S Red Dots installed..

This optic plate is made to REPLACE the rear sight of Ruger LC9, LC9s, and LC380 Pistols. Over the different productions, LC9 sometimes changed the tolerance of the dovetail width slightly. It is common after retooling the machine when switching the productions for different parts. The easiest way to solve the problem is to punch a small hole near any edge, to create a small, protruded bump on the insert where it slides into the dovetail.. The JPoint, Shield RMSc, Shield SMSc, Shield RMS2, Romeo Zero, Romeo X SORX1200 only, Vortex Defender CCW, Holosun 507K, Holosun 407K, Sightmark Mini, Riton MPR D2, Riton 3 Tactix MPRD, Swampfox Sentinal, HEX Wasp, Cyelee CAT PRO, Crimson Trace CTS-1550, and ADE RD3-018 Spike, RD3-021 Nuwa, RD3-021 PRO, RD3-030 Apollo mount using the rear set of mounting holes and do not use the locating pins at the front of the plate. . Fit Ade RD3-006AHuracan, RD3-006BPython, RD3-009Crusader, RD3-012Delta, RD3-013Bertrillium, RD3-015ZantitiumRed dots. Also Fit JPoint, Shield RMSc, Shield SMSc, Shield RMS2, Romeo X SORX1200 only, Vortex Viper, Vortex Venom, Vortex Defender CCW, Holosun 507K, Holosun 407K, Romeo Zero, DocterNoblex Sight C, DocterNoblex sight 2, DocterNoblex sight III, DocterNoblex QUICKsight 5.0 VR, Noblex Sight G, Burris Fastfire 2, Burris Fastfire 3. Also Fits Delta Optical MiniDot, Delta Optical MiniDot II, Hawke Reflex 125, Sightmark Mini Shot Pro Spec, Sightmark Mini Shot M-Spec, Leica Tempus, MAKdot 125, Vector Optics SCRD-19II Frenzy 1x17x24, Creative XP GlassEagle HD, Riton MPR D2, Riton 3 Tactix MPRD, Swampfox Sentinal, HEX Dragonfly, HEX Wasp, Crimson Trace CT RAD Pro, Crimson Trace CTS-1550, Crimson Trace CTS-1250, Cyelee CALF V2, Cyelee CAT PRO, or Vomz Pilad 120..

Precision CNC Machined from Aircraft Grade Aluminum. This optic picatinny mount made by ADE is to connect to certain type of optic sight to standard 1913 picatinnyweaver rail. It does not connect to handgun because most handguns does NOT has a picatinny rail on top. Designed to use on ADE RD3-018 SPIKE, Shield RMSRMScRMSwSMS and Romeo Zero Red dot sights.. Also Compatible with Leupold Delta Point Pro, JP Enterprises JPoint and Swampfox Sentinel red dot sights. Does NOT compatible with Holosun 407k507k, user MUST grindlots of grinding to completely REMOVEFlat out the two rear pin to fit 407k507k. Ade has is releasing a new plate made specifically for 407k507k in March 2022. Finished in a Matte Black Anodize. Comes with two screws.

This plate is for Ruger 57 pistol ONLY, it does not fit any other pistols.. The plate is compatible with RD3-020 Raptor, RD3-023 Valkyrie, RD3-019 Stingray, Trijicon RMRSRO, Holosun HS407CHS507CHS508T, Riton X3 Tactix PRD, Trijicon RMRSRO, Swampox KingslayerLibertyJustice red dot sight and Holosun 407C507C. Screws are provided for Trijicon, Holosun 407C507C and ADE. The provided screws may NOT work other red dots listed. If not, we recommend get the right size screws from a local hardware store.. The footprint of this plate is NOT compatible with other footprints. This plate does NOT fit other red dots such as Vortex VenomViper, Doctor, Burris Fastfire, Shield RMSRMSc, Trijicon RMRcc, Deltapoint Pro, Swapfox sentinel, ADE Spike, Holosun 407k507k.. Precision machined out of 6061 aluminum. Weight .4oz.40grain ammo may be necessary for proper cycling due to heavy RMR sights.

Optic Shim is made to fit between the red dot and the mounting plate.. Fits Shield RMSRMSCRMSWSMS, ADE RD3-018 SPIKE, Sig Sauer Romeo Zero, Leupold Delta Point Pro, JP Enterprises JPoint, Swampfox Sentinel Red dot Sight. All trademarks mentioned belong to their respective owner, this optic shim is made by ADE as a mounting accessory for the mentioned optics. Does NOT fit Trijicon RMRSRO, Doctor, Vortex VenomViper, Burris Fastfire, ADE RD3-006009012013. Depending on the handgun, some handguns need THIS 1degree shim to give extra range of elevation across a wide range of firearms such as the 1911. Should you feel any resistance from the mechanism whilst zeroing the elevation please fit the shim between the sight and the mount with the thickest part at the rear.. What it does While zeroing the red dot sight, some users turned the elevation screw all the way to the end that can no longer turnscrew maxed-out, the location of the illuminated dot is still TOO HIGH, user is UNABLE to adjust the dot LOW enough to zero. Instead of returning the defective red dot, this shim will rise the optic to help user to move the illuminated dot higher to the location to zero. .. Scope base shims Tolerance -.005 Taper 1.0 degree.

Designed for Springfield Hellcat OSP with Optic Cut space for keeping the red dot installed for every day carry. Also fit Non-OSPNon-Optics Ready Hellcat. This IWB Optics Ready holster is compatible with red dots such as Shield RMSRMSCRMSWSMS, Sig Saure Romeo Zero, JP Enterprises JPoint, Swampfox Sentinel, ADE RD3-018 SPIKE, Leupold Delta Point Pro, Vector Optics Frenzy-S Red Dots installed.. Thick .08 Kydex material that is strong, durable, and molded specifically for your weapon. Adjustable Retention so you can get the perfect fit. Package includes holster plus hex adjustment tool.. Fully covers trigger and backside of gun, providing safety and protection from sweat. Adjustable Cant From -5 to 20 Degrees This slight adjustment from -5 to 20 degrees will help angle your holster perfectly for ApprndixAIWB, Strong Side, Behind The Hip or Cross Draw. Fits 1.5 Width Belt. No Risk of Pressing Release. AUDIBLE CLICK AND SECURE RETENTION Audible click sound ensures your firearm is safe and secure every time you reholster..

Designed to fit Holosun 407k507k and any red dot with the same footprint. Also works with Holosun ESP red dot.. This optic mount made by ADE is to connect to certain type of optic sight. It does not connect to handgun because most handguns does NOT has a rail on top. Also Compatible with Leupold Delta Point Pro, JP Enterprises JPoint and Swampfox Sentinel red dot sights. Finished in a Matte Black Anodize. Comes with two screws. Also Compatible with ADE RD3-018 SPIKE, Shield RMSRMScRMSwSMS and Romeo Zero Red dot sights..

Ade Stingray is Designed to to the smallest and lightest red dot to fit any pistol mounting plateslidecut that is compatible with RMRSRO, Holosun 407C507C508T footprint red dots. The overall length is around 15-20 shorter than other major competitors. The shorter design allow this sight to be able to sit in to all optic cutsplatesadapters that designed for rmr. For some optics ready pistols with a large optic cut, there will be a gap between the optic rear dot and pistol rear iron sight.. Ade Stingray created a iron sight curve at the end of the body, and also added two white dots on the curve. For the rear of part of the red dot to become a back up iron sight. With the ultra short design, the red dot provides a distancegap on some of full size optics ready pistol, to give enough distance to be a Co-Witness back up sight, in addition to the LED dot and pistol equipped iron sight.. For non-optics ready pistols that need to use an optic plateadapter to replace the pistol manufacture equipped rear sight, ADE Stingray's rear white dot will acts as a pistol factory original rear sight for Co-Witness. Does NOT fit optic platecut made for Doctor type footprint. Comes with screws for several Optics Ready handguns. Does not comes with any mounting plate such as picatinny mount or plate made for a specific handgun.. One year battery life with a single CR2032 batteryincluded. ADE Stingray GREEN dot sight is always powered on with automatic brightness. Operates with a single CR2032 3v battery. With our advanced technology the sight only draws approximate 700 microampere powers to give a very long battery life. The brightness will turn high and low accordingly to the environment brightness.. Just like 400 RMR competitors, It does not has a onoff power button. The light turns brighter or lower automatically. If you do not use it, put the provided rubber cover on it, then the sight will be sleeping in a very very low power mode. Weight approximately .88oz25grams. Hard coated aircraft aluminum and multi-coated glass. Not plastic body with polymer lens. 6 MOA RED dot. Length1.6 x Width1.1 x Height.93. Ade SPIKE created an iron sight curve at the end of the body, and also added two white dots on the curve. For the rear of part of the red dot to become a back up iron sight. With the ultra short design, the red dot provides a distancegap on some full size optics ready pistols, to give enough distance to be a Co-Witness back up sight, in addition to the LED dot and pistol equipped iron sight. For non-optics ready pistols that need to use an optic plateadapter to replace the pistol manufacturer equipped rear sight, ADE Stingray's rear white dot will act as a pistol factory original rear sight for Co-Witness..

Precision CNC Machined from Aircraft Grade Aluminum with Weight Reducing Trapezoid Cuts This is an riser Optic Mount to attach to the red dot sights to lift the red dot higher to absolute Cowitness level.. This is a PICATINNY rail mount. The red dot optic MUST equipped with a PICATINNY BASE in order to attach to this riser mount.. Some of the red dots comes with picatinny plate with the red dot purchase, such as Vortex Venom and Burris Fastfire. This Picanny riser will fit the red dot factory provided original pictainny plate.. Some of the red dots do NOT come with picatinny plate with the red dot purchase, such as holosun 407k. User need to purchase the picatinny plate separately in order to attach to this riser mount.. Finished in a Matte Black Anodize. Comes with installation screws and allen wrench..

This is a optic mounting plate for Glock that replaces the factory rear sight dovetail of all Non-MOS Glocks from Glock 17 to Glock 43 to glock 100. Does NOT fit Glock with AFTERMARKET slide. Installing the aftermarket red dot plate is not simply plug and play. We recommend having a qualified gunsmith to install. The included Glock plate fit some other Pistols such as Canik TP9SFdoes not fit SFX, COMBAT, SA. This Glock plate also fits Taurus GX4, G3C G3 with factory steel sights does not fit any other Taurus models such as G2G2CG3 without factory steel sightTx22PT111 because those pistols made the rear sight dovetail based on the Glock rear sight dovetail specifications.. This optic dovetail plate made by ADE only fits genuinestandard glock that has a standard factory rear sight. It does NOT for MOSoptics ready glock. It does NOT fit glock with AFTERMARKET slide.. Compatible with Holosun 407k507k, Shield RMSCRMS, Sig Romeo Zero, ADE RD3-018 SPIKE, RD3-021 NUWAScrew provided for ADE, Shield, Sig and Holosun. Also compatible with other red dots that shares the similar footprint, but provided screws may NOT work, such as JPOINT4, Swampfox Sentine, CT1550, Riton X3 Tactix MPRD. We recommend get the right size screws from a local hardware store.. The footprint of this plate is NOT compatible with other footprints. This plate does NOT fit other red dots such as Vortex VenomViper, Doctor, Burris Fastfire, Trijicon RMRSRO, Holosun 407c507c, ADE RD3-006009012011013015019023.

This Optics Mount Plate is designed to connect Optics Red Dot Reflex Sight to Ruger Security 9 full size and compact size pistols by Replacing the Rear Sight with this Optic Mounting Plate.. Attention This Ruger Security 9 optic plate does NOT fit Ruger SR9 pistol. Ruger SR9 and Ruger Security 9 are completely two different pistols. Torque screw to 15inchlb. For gun glue, we recommend to use loctite treadlocker. This plate fits Vortex ViperVenom, ADE RD3-003,RD3-006, ADE RD3-009,RD3-012and Pro,RD3-015and Pro, RD3-028, RD3-018 Spike, , DocterNoblex Sight C, DocterNoblex sight 2, DocterNoblex sight III,QUICKsight 5.0 VR, Noblex Sight G,Burris Fastfire 2, 3, Delta Optical MiniDot,Delta Optical MiniDot II,Hawke Reflex,Sightmark Mini Shot Pro Spec,Mini Shot M-Spec,Leica Tempus, MAKdot, Vector Optics SCRD-19II Frenzy,Creative XP GlassEagle HD, HEX Dragonfly,CT RAD Pro, Cyelee CALF V2,Vomz Pilad.. Also fits Burris Fastfire 2, Burris Fastfire 3, Delta Optical MiniDot, Delta Optical MiniDot II, Hawke Reflex 125, Sightmark Mini Shot Pro Spec, Sightmark Mini Shot M-Spec, Leica Tempus, MAKdot 125, Vector Optics SCRD-19II Frenzy 1x17x24, Creative XP GlassEagle HD, Riton MPR D2, Riton 3 Tactix MPRD, Swampfox Sentinal, HEX Dragonfly, HEX Wasp, Crimson Trace CT RAD Pro, Cyelee CALF V2, Cyelee CAT PRO, or Vomz Pilad 120.. Comes with several pairs of screws for ADE, Shield, Holosun, Vortex, Burris red dots. The screws should fits most of the listed red dot but not guaranteed for every red dot. If you need the longershorter screw to work properly, we recommend going to a local hardware store such as ACE Hardware to get the right size..

Precision CNC Machined from Aircraft Grade Aluminum with Weight Reducing Trapezoid Cuts. This is an riser Optic Mount to attach to the red dot sights to lift the red dot higher to absolute level.. Designed exclusively to fit Holosun 407k507k and any red dot with the same footprint.. Compatible with Shield RMSCRMS, Sig Romeo Zero, ADE RD3-018 SPIKE, RD3-021 NUWAScrew provided for ADE, Shield, Sig and Holosun. Also compatible with other red dots that shares the similar footprint, but provided screws may NOT work, such as JPOINT4, Swampfox Sentine, CT1550, Riton X3 Tactix MPRD. We recommend get the right size screws from a local hardware store.. The footprint of this plate is NOT compatible with other footprints. This plate does NOT fit other red dots such as Vortex VenomViper, Doctor, Burris Fastfire, Trijicon RMRSRO, Holosun 407c507c, ADE RD3-006009012011013015019023.

Fully windage and elevation adjustable and lockable Unlimited Eye Relief. Multi Illumination Settings. Powered by a lithium CR2032 batteryIncluded.It is also compatible with varies handgun mounting plates that replace rear sight dovetail.. This Huracan Green Dot Sight fits directly to Optics Ready pistols that does not need to remove rear sight such as Glock MOS, Springfield OSP. It also fits Canik using Canik provided mount marked for DoctorVenom type red dot.. However the front switch of the sight needs to trim down 2mm depends on exact pistol model if the pistol's pre-cut is very short... Comes with an removable picatinny mounting base to attach to any thing with piatinny rail. Fully windage and elevation adjustable and lockable Unlimited Eye Relief. Powered by a lithium CR2032 battery. ADE RD3 006,RD3 009,RD3 012,RD3 013,RD3 015 are designed to fit the slidefootprint of plate made for Vortex Venom,Burris Fastfire,Meopta,Docter,Insight,Eotech MRDS.Any Plate made for those brands also fits this sight..

We have made several improvements since it's initial release in 2014. We have made it more durable to withstand recoil and improved the ability to hold zero. Designed in Oregon.. WaterproofShockFog Resistant. Lenses are precision ground and polished to exacting geometries to virtually eliminate parallax and to provide a very clear, crisp sight picture.. This red dot comes with a picatinny mounting base. It is also compatible with varies handgun mounting plates that replace rear sight dovetail. It is also compatible to Optics Ready pistols such as Glock MOS, Springfield OSP,. Fully windage and elevation adjustable and lockable Unlimited Eye Relief. 5 MOA. 5 Illumination Settings. Powered by a lithium CR2032 batteryIncluded. Ade model RD3-006,RD3-009,RD3-012,RD3-013,RD3-015 are designed to fit the slidefootprint of plate made for Vortex Venom,Burris Fastfire,Meopta,Docter,Insight,Eotech MRDS. Any Plate made for those brands also fits this sight..

Optic Shim is made to fit between the red dot and the mounting plate.. Fits Shield RMSRMSCRMSWSMS, ADE RD3-018 SPIKE, Sig Sauer Romeo Zero, Leupold Delta Point Pro, JP Enterprises JPoint, Swampfox Sentinel Red dot Sight. All trademarks mentioned belong to their respective owner, this optic shim is made by ADE as a mounting accessory for the mentioned optics. Scope base shims Tolerance -.005 Taper 1.0 degree. What it does While zeroing the red dot sight, some users turned the elevation screw all the way to the end that can no longer turnscrew maxed-out, the location of the illuminated dot is still TOO HIGH, user is UNABLE to adjust the dot LOW enough to zero. Instead of returning the defective red dot, this shim will rise the optic to help user to move the illuminated dot higher to the location to zero. Scope base shims Tolerance -.005 Taper 1.0 degree.. Depending on the handgun, some handguns need THIS 1degree shim to give extra range of elevation across a wide range of firearms such as the 1911. Should you feel any resistance from the mechanism whilst zeroing the elevation please fit the shim between the sight and the mount with the thickest part at the rear..

Precision CNC Machined from Aircraft Grade Aluminum with Weight Reducing Trapezoid Cuts. This is an riser Optic Mount to attach to the red dot sights to lift the red dot higher to absolute level.. Designed exclusively to fit Holosun 407k507k and any red dot with the same footprint.. Compatible with Shield RMSCRMS, Sig Romeo Zero, ADE RD3-018 SPIKE, RD3-021 NUWAScrew provided for ADE, Shield, Sig and Holosun. Also compatible with other red dots that shares the similar footprint, but provided screws may NOT work, such as JPOINT4, Swampfox Sentine, CT1550, Riton X3 Tactix MPRD. We recommend get the right size screws from a local hardware store.. The footprint of this plate is NOT compatible with other footprints. This plate does NOT fit other red dots such as Vortex VenomViper, Doctor, Burris Fastfire, Trijicon RMRSRO, Holosun 407c507c, ADE RD3-006009012011013015019023.

This is RD3-012G is GREEN DOT model, there is also a RD3-012 Red dot. The sight has multi brightness level with TWO adjustment button. One to turn bright up and one to turn down. Hold the down button for 3 secs to power off. Every time you turn on the dot it stays the same brightness level last time it was turned off. Comes with a picatinny mounting base. It is also compatible with varies handgun mounting platesSOLD SEPARATELY that replace rear sight dovetail. It is also compatible to Optics Ready pistols such as Glock MOS, Springfield OSP, Taurus TORO using Pistol manufacturer provided optic mounting plateSOLD SEPARATELY.. This GREEN dot fits directly on Glock MOS system with the 1 mount that comes with MOS without needing to remove the rear sight. This glock MOS 01 plate need to obtain from glock, not included in this green dot purchase.. Promotes rapid target acquisition while providing a precise point of aim getting shots down range and on target fast. Top load System, no need to Remove the sight to change the Battery that requires re-sight in and waste ammo.. GREEN dot has multi brightness level with one adjustment button. Every time you turn on the dot it stays the same brightness level last time it was turned off. While it is possible to install the optic to handgun without the use of a Gunsmith, we recommend hiring a professional gunsmith. Please note. Unprofessional installation such as improper torque will result in screw loose, not holding zero, damage to the firearmoptic and personal injury.. ADE RD3-006B, RD3-009, RD3-012, and RD3-013 fit optic cutplate that is compatible with Vortex VenomBurris FastfireDoctor footprint. ADE RD3-018 Spike, RD3-021 Nuwa fit optic cutplate that is compatible with Shield RMSRMSCLeopold Deltapoint ProSig Romeo Zero footprint. ADE RD3-019 Stingray, RD3-020 Raptor, RD3-023 Valkyrie Gen2 fit optic cutoptic plate that is compatible with Trijicon RMR HS407CHS507CHS508T footprint.

ADE is releasing the 2023 PRO SERIES for ADE RD3-0122016-present Delta red dot called Delta PROD3-012PRO. The additional features that the PRO series includes are Motion Activated System, IP67 Waterproof, and Multi Reticle Technology.. Top load System, no need to Remove the sight to change the Battery. Comes with Red dot, tool, removeable picatinny plate with two screws, cover, lens cloth and instruction manual. Fits pistol optic platecut that is compatible with DoctorVortex VenomBurris Fastfire footprint. Does NOT fit optic platecut for RMR, Shield RMS type footprints.. The ADE Delta PROD3-012PRO has Motion Activated System. While Delta PRO is turned on, the red dot illumination goes to sleep after five minutes of inactivity, but when any motion or vibration is detected, it instantly switches on illumination at the previous brightness setting.. The reticle can be switched between a 32 MOA circle with 2 MOA dot, a 2 MOA dot only, or a 32 MOA ring only at the push of a button. Better yet, the same LED projects both reticles, so no re-zeroing is necessary. Operates with a single CR1632 battery. Press and Hold the DOWN switch for 3 seconds to manually turn onoff the power. Press and Hold the UP switch for 3 seconds to change reticle. Quick press UpDown switches to adjust brightness.. 1.75 length x1.25 width x1.15 height. IP67 Waterproof. The lens is coated with multi-coating to eliminate glare and provide a high level of performance in low light..

This green dot sight comes equipped with a Picatinny mounting base and is also compatible with various handgun mounting plates that replace the rear sight dovetail. It's designed to fit the Doctor Footprint PlateSlide seamlessly.. The onoff switch for this sight is conveniently positioned at the front, making it much easier to press compared to red dots with side-mounted switches. It features a 3 MOA dot size and offers 5 illumination settings. The sight is fully adjustable for windage and elevation and can be locked into place. With unlimited eye relief and various illumination settings, it is powered by an included lithium CR2032 battery.. Since its initial release in 2014, we've implemented numerous improvements to enhance its durability, ensuring it can withstand recoil while also improving its ability to hold zero. The front switch, battery housing, and hardware have all been recently updated, reflecting our commitment to continuous enhancement. This product is proudly designed in Oregon.. Although it's feasible to install the optic on a handgun without the assistance of a gunsmith, we highly recommend seeking the expertise of a professional for the installation process. It's essential to note that unprofessional installations, such as improper torque application, can lead to issues like loose screws, an inability to hold zero, damage to the firearm or optic, and even pose a risk of personal injury.. If you're not seeing a perfect round dot but instead observe a splashed dot, half-moon shape, multi-dot, or starburst, there's a high probability 99 that you might have astigmatism without being aware of it. What you perceive is likely a small reflection of the LED light on the lens. A quick and simple way to confirm this is by using your cellphone to take a photo of the dot. If the photo shows a circular dot, you've essentially diagnosed yourself with astigmatism.. ADE RD3-006 Huracan,RD3-009 Crusader,RD3-012 Delta, RD3-012 PRO, RD3-013 Bertrillium ,RD3-015 Zantitium, RD3-028 Ares fit optic cutplate that is compatible with Vortex VenomBurris FastfireDoctor footprint. ADE RD3-018 Spike, RD3-021 Nuwa, RD3-021 NUWA PRO and RD3-030 Apollo fit optic cutoptic plate that is compatible with shield RMSRMSCDeltapoint Pro footprint. ADE RD3-021c NUWAcc fits optic cutoptic plate that is compatible with Trijicon RMRcc footprint. ADE RD3-019 Stingray, RD3-020 Raptor, RD3-022 Artemis, RD3-023 Valkyrie and RD3-029 Trumpet fit optic cutoptic plate that is compatible with Trijicon RMRSROHolosun 407C507C footprint.

This FDETAN body color RED Dot is one of ADE's newest product in 2022. ADE is now offering FDE body color optics for several of ADEs popular red dot models. The FDE standards for Flat Dark Earth, it is a Tan-ish color. This ADEs FDE color will not 100 match every FDE color handgun on the market because every handgun company made their FDE color proprietary, however, it will look great even the color might be slightly darker or lighter. ADE Spike also available in Black body and RED Dot. Designed to fit Canik Elite TP9 SC, Canik METE SFX, Canik METE SFT, Sig P365XLP365X, Ruger Max-9, Glock 43X MOS48 MOSnot compatible with regular glock 43x48 that are not MOS, Springfield Hellcat OSP, SW Shield 2.0 Optics Ready, SW MP9 EZ, SW MP shield plus performance center, Walther PPS M2 Optics Ready, Girsan MC1911SC Ultimate or any pistolmounting plateslide with RMSRMSC screw patternfootprint.. Hard coated aircraft aluminum in FDE body and multi-coated glass. Not plastic body with polymer lens.. ADE SPIKE red dot sight is always powered on with automatic brightness. Operates with a single CR2032 3v battery. With our advanced technology the sight only draws approximate 700 microampere powers to give a very long battery life. The brightness will turn high and low accordingly to the environment brightness.. 4MOA, Weight approximately 17.6 grames0.62oz, Length1.6 x Width.92 x Height.93. Ade SPIKE created an iron sight curve at the end of the body, and also added two white dots on the curve. For the rear of part of the red dot to become a back up iron sight. With the ultra short design, the red dot provides a distancegap on some full size optics ready pistols, to give enough distance to be a Co-Witness back up sight, in addition to the LED dot and pistol equipped iron sight. For non-optics ready pistols that need to use an optic plateadapter to replace the pistol manufacturer equipped rear sight, ADE Spike's rear white dot will act as a pistol factory original rear sight for Co-Witness.. Comes with screws for several Optics Ready handguns. Does not comes with any mounting plate such as picatinny mount or plate made for a specific handgun.. Comes with 3 pairs of screws for Sig P365XLX, Springfield Hellcat OSP and Canik TP9 Elite SC ONLY. The provided screws might NOT work with EVERY compatible pistol listed. ADE makes the red dot to accept the industrial standard footprint. The pistol manufacturer makes the optic cutslide for the same footprint, but they have their own opinions to decide which type screws that the screw holes take.. ADE Does not know the screw spec every pistol manufacture used for their screw hole. Please ask the pistol manufacture what screw specs they used on the hole and ask them to provide the screw. If you cant get the screw to work properly, we recommend going to a local hardware store such as ACE Hardware to get the right size..

DURABLE BUILT TO LAST-- Super durable braided fiber laces with tight molded tips and high performance paraffin wax. SIZE OPTIONS-- Come in five size options so you can match your skate dimensions perfectly. COLOR OPTIONS-- Featuring six vibrant color variations for maximum skate visual customization. SET-- All laces come in pairs. For all types of skates roller skate, inline, roller blade, ice, hockey, etc.. QUALITY GUARANTEE-- We provide only high-quality skate laces. If you are not fully satisfied for any reason, just contact us by Amazon messaging within 30 days for a full refund of your purchase price..

Designed to fit Canik Elite TP9 SC, Canik METE SFT, Sig P365XLP365X, Ruger Max-9, Glock 43X MOS48 MOSnot compatible with regular glock 43x48 that are not MOS, Springfield Hellcat OSP, SW Shield 2.0 Optics Ready, SW MP9 EZ, SW MP shield plus performance center, Walther PPS M2 Optics Ready, Girsan MC1911SC Ultimate or any pistolmounting plateslide with RMSRMSC screw patternfootprint.. Hard coated aircraft aluminum and multi-coated glass. Not plastic body with polymer lens.. ADE SPIKE red dot sight is always powered on with automatic brightness. Operates with a single CR2032 3v battery. With our advanced technology the sight only draws approximate 700 microampere powers to give a very long battery life. The brightness will turn high and low accordingly to the environment brightness.. 4MOA, Weight approximately 17.6 grames0.62oz, Length1.6 x Width.92 x Height.93. Comes with screws for several Optics Ready handguns. Does not comes with any mounting plate such as picatinny mount or plate made for a specific handgun.. Ade SPIKE created an iron sight curve at the end of the body, and also added two white dots on the curve. For the rear of part of the red dot to become a back up iron sight. With the ultra short design, the red dot provides a distancegap on some full size optics ready pistols, to give enough distance to be a Co-Witness back up sight, in addition to the LED dot and pistol equipped iron sight. For non-optics ready pistols that need to use an optic plateadapter to replace the pistol manufacturer equipped rear sight, ADE Spike's rear white dot will act as a pistol factory original rear sight for Co-Witness.. Comes with 3 pairs of screws for Sig P365XLX, Springfield Hellcat OSP and Canik TP9 Elite SC ONLY. The provided screws might NOT work with EVERY compatible pistol listed. ADE makes the red dot to accept the industrial standard footprint. The pistol manufacturer makes the optic cutslide for the same footprint, but they have their own opinions to decide which type screws that the screw holes take.. ADE Does not know the screw spec every pistol manufacture used for their screw hole. Please ask the pistol manufacture what screw specs they used on the hole and ask them to provide the screw. If you cant get the screw to work properly, we recommend going to a local hardware store such as ACE Hardware to get the right size..

Designed to fit Canik Elite TP9 SC, Canik METE SFT, Sig P365XLP365X, Ruger Max-9, Glock 43X MOS48 MOSnot compatible with regular glock 43x48 that are not MOS, Springfield Hellcat OSP, SW Shield 2.0 Optics Ready, SW MP9 EZ, SW MP shield plus performance center, Walther PPS M2 Optics Ready, Girsan MC1911SC Ultimate or any pistolmounting plateslide with RMSRMSC screw patternfootprint.. Hard coated aircraft aluminum and multi-coated glass. Not plastic body with polymer lens.. ADE SPIKE red dot sight is always powered on with automatic brightness. Operates with a single CR2032 3v battery. With our advanced technology the sight only draws approximate 700 microampere powers to give a very long battery life. The brightness will turn high and low accordingly to the environment brightness.. 4MOA, Weight approximately 17.6 grames0.62oz, Length1.6 x Width.92 x Height.93. Comes with screws for several Optics Ready handguns. Does not comes with any mounting plate such as picatinny mount or plate made for a specific handgun.. Ade SPIKE created an iron sight curve at the end of the body, and also added two white dots on the curve. For the rear of part of the red dot to become a back up iron sight. With the ultra short design, the red dot provides a distancegap on some full size optics ready pistols, to give enough distance to be a Co-Witness back up sight, in addition to the LED dot and pistol equipped iron sight. For non-optics ready pistols that need to use an optic plateadapter to replace the pistol manufacturer equipped rear sight, ADE Spike's rear white dot will act as a pistol factory original rear sight for Co-Witness.. Comes with 3 pairs of screws for Sig P365XLX, Springfield Hellcat OSP and Canik TP9 Elite SC ONLY. The provided screws might NOT work with EVERY compatible pistol listed. ADE makes the red dot to accept the industrial standard footprint. The pistol manufacturer makes the optic cutslide for the same footprint, but they have their own opinions to decide which type screws that the screw holes take.. ADE Does not know the screw spec every pistol manufacture used for their screw hole. Please ask the pistol manufacture what screw specs they used on the hole and ask them to provide the screw. If you cant get the screw to work properly, we recommend going to a local hardware store such as ACE Hardware to get the right size..

Designed to fit Canik Elite TP9 SC, Canik METE SFT, Sig P365XLP365X, Ruger Max-9, Glock 43X MOS48 MOSnot compatible with regular glock 43x48 that are not MOS, Springfield Hellcat OSP, SW Shield 2.0 Optics Ready, SW MP9 EZ, SW MP shield plus performance center, Walther PPS M2 Optics Ready, Girsan MC1911SC Ultimate or any pistolmounting plateslide with RMSRMSC screw patternfootprint.. Hard coated aircraft aluminum and multi-coated glass. Not plastic body with polymer lens.. ADE SPIKE red dot sight is always powered on with automatic brightness. Operates with a single CR2032 3v battery. With our advanced technology the sight only draws approximate 700 microampere powers to give a very long battery life. The brightness will turn high and low accordingly to the environment brightness.. 4MOA, Weight approximately 17.6 grames0.62oz, Length1.6 x Width.92 x Height.93. Comes with screws for several Optics Ready handguns. Does not comes with any mounting plate such as picatinny mount or plate made for a specific handgun.. Ade SPIKE created an iron sight curve at the end of the body, and also added two white dots on the curve. For the rear of part of the red dot to become a back up iron sight. With the ultra short design, the red dot provides a distancegap on some full size optics ready pistols, to give enough distance to be a Co-Witness back up sight, in addition to the LED dot and pistol equipped iron sight. For non-optics ready pistols that need to use an optic plateadapter to replace the pistol manufacturer equipped rear sight, ADE Spike's rear white dot will act as a pistol factory original rear sight for Co-Witness.. Comes with 3 pairs of screws for Sig P365XLX, Springfield Hellcat OSP and Canik TP9 Elite SC ONLY. The provided screws might NOT work with EVERY compatible pistol listed. ADE makes the red dot to accept the industrial standard footprint. The pistol manufacturer makes the optic cutslide for the same footprint, but they have their own opinions to decide which type screws that the screw holes take.. ADE Does not know the screw spec every pistol manufacture used for their screw hole. Please ask the pistol manufacture what screw specs they used on the hole and ask them to provide the screw. If you cant get the screw to work properly, we recommend going to a local hardware store such as ACE Hardware to get the right size..

Precision CNC Machined from Aircraft Grade Aluminum. This optic picatinny mount made by ADE is to connect to certain type of optic sight to standard 1913 picatinnyweaver rail. It does not connect to handgun because most handguns does NOT has a picatinny rail on top. Designed to use on ADE RD3-018 SPIKE, Shield RMSRMScRMSwSMS and Romeo Zero Red dot sights.. Also Compatible with Leupold Delta Point Pro, JP Enterprises JPoint and Swampfox Sentinel red dot sights.. Finished in a Matte Black Anodize. Comes with two screws.

Precision CNC Machined from Aircraft Grade Aluminum. This optic picatinny mount made by ADE is to connect to certain type of optic sight to standard 1913 picatinnyweaver rail. It does not connect to handgun because most handguns does NOT has a picatinny rail on top. Designed to use on ADE RD3-018 SPIKE, Shield RMSRMScRMSwSMS and Romeo Zero Red dot sights.. Also Compatible with Leupold Delta Point Pro, JP Enterprises JPoint and Swampfox Sentinel red dot sights. Finished in a Matte Black Anodize. Comes with two screws. Wrong Inventory fixed, customer will receive correct footprint for RMS, not RMR.

ADE RD3-023 Valkyrie is a 4 MOA GREEN dot designed to fit any Optics Ready pistol with a PISTOL MANUFACTURER PROVIDED mounting plate that is compatible with RMRSRO, Holosun 407C507C508T footprint red dots. The Valkyrie does NOT fit any AFTERMARKET NON-Genuine slide that has a optic cut PRECISELY MILLED for the EXACT DIMENSIONLENGTH of Trijicon RMR because Valkyrie is about 1mm longer which prevent it to sit into the shorter cut.. The Valkyrie ONLY fits name brand pistol manufacturer made Optics Ready pistols, such as Glock MOS, SW MP 2.0 OP, IWI Masada, Smith Wesson MP C.O.R.E, CZ P10F10C optics ready, Walther Q5 Match and Springfield XDXDMXDS OSP, Canik TP9 SFXCombat, FN 50945 Tactical, Shadow Systems MR 920.. Those name brand pistol manufacturer made Optics Ready handguns all come with several mounting platesoptic cuts marked for different brands of red dots, such as for Trijicon RMR, Shield RMS and Vortex Venom red dot footprint. The Valkyrie fits one of the pistol manufacturer provided plate marked that is compatible with Trijicon RMR.. ADE Valkyrie created a iron sight curve at the end of the body, and also added two white dots on the curve. For the rear of part of the red dot to become a back up iron sight to give enough distance to be a Co-Witness back up sight, in addition to the LED dot and pistol equipped iron sight.. For non-optics ready pistols that need to use an optic plateadapter to replace the pistol manufacture equipped rear sight, ADE Valkyrie's rear white dot acts as a pistol factory original rear sight for Co-Witness. 4 MOA GREEN Dot. Comes with a picatinny mounting plate and a pair of screws. This red dot does NOT comes with any other optic plate to mount on an specific pistol. Operates with a single CR2032 batteryinstall underneath. Gives around 800 hour battery life. Auto powers off after 1 hour of inactivity to save battery.. Dimension 1.79x1.18x1.4 inches. Weight 1.24 oz. ShockproofFogproof. This model is the original ADE Valkyrie, ADE also have a ADE Valkyrie Gen2. The difference between ADE Valkyrie and ADE Valkyrie Gen2 is that the Gen2 is slightly shorter in overall length, and the shorter length allows Gen2 to sit into custom RMR cut, while original Valkyrie only fits optic plate for RMR footprint..

This listing comes with ADE red dot, a picatinny mounting platepre-assembled and a pistol mounting plate for Glock that replaces the factory rear sight dovetail of all Non-MOS Glocks from Glock 17 to Glock 43 to glock 100. Does NOT fit Glock with AFTERMARKET slide with optic cut.. The included Glock plate also fit some other Pistols such as Canik TP9SFdoes not fit SFX, COMBAT, SA. This Glock plate also fits Taurus GX4, G3C G3 with factory steel sights does not fit any other Taurus models such as G2G2CG3 without factory steel sightTx22PT111 because those pistols made the rear sight dovetail based on the Glock rear sight dovetail specifications. While it is possible to install this mount without the use of a Gunsmith, we recommend hiring a professional gunsmith. We have made several improvements since it's initial release in 2015. We have made it more durable to withstand various recoil and improved the ability to hold zero. Designed in Oregon. The onoff switch is located at the front of the sight, it is so much easier to press than the Red dots has the switches on the side.. ShockFog Proof. It is rain resistant, but not waterproof. Lenses are precision ground and Polished to exacting geometries to virtually eliminate Parallax and to provide a very clear, crisp sight picture. 4 MOA. 5 Illumination Settings. Powered by a lithium CR2032 batteryIncluded. Why dont I see a perfect round dot Instead, I see a splashed dot, half-moon shape, multi dot, starburst etc. Answer It is very likely 99 chance you have astigmatism that you are not aware. What you see is a led light image reflected on the lens. One simple way to find out is to use your cellphone to take a photo of the dot. If you see a circle dot in the photo you took, you basically diagnosed you have AstigmatismBecause cellphone is a machine does not has human astigmatism.. Many users with astigmatism decide to continue to use the imperfect dot, or use a bigger MOA red dot such as 6MOA instead of 3MOA. Some users also see green dots better than red dots, it really depends on the individual case. Or users can use a totally different optics which is not a reflex sight such as a rifle scope..

This is ADE's new GREEN dot version of RD3-018 Spike. The Spike now available in 3 models. Black body 4MOA Red dot, Black body 4MOA GREEN dotthis one and FDETAN body 4MOA Red dot.. Designed to fit Canik Elite TP9 SC, Canik METE SFX, Canik METE SFT, Sig P365XLP365X, Ruger Max-9, Glock 43X MOS48 MOSnot compatible with regular glock 43x48 that are not MOS, Springfield Hellcat OSP, SW Shield 2.0 Optics Ready, SW MP9 EZ, SW MP shield plus performance center, Walther PPS M2 Optics Ready, Girsan MC1911SC Ultimate or any pistolmounting plateslide with RMSRMSC screw patternfootprint.. Hard coated aircraft aluminum and multi-coated glass. Not plastic body with polymer lens.. ADE SPIKE red dot sight is always powered on with automatic brightness. Operates with a single CR2032 3v battery. With our advanced technology the sight only draws approximate 700 microampere powers to give a very long battery life. The brightness will turn high and low accordingly to the environment brightness.. 4MOA, Weight approximately 17.6 grames0.62oz, Length1.6 x Width.92 x Height.93. Ade SPIKE created an iron sight curve at the end of the body, and also added two white dots on the curve. For the rear of part of the red dot to become a back up iron sight. With the ultra short design, the red dot provides a distancegap on some full size optics ready pistols, to give enough distance to be a Co-Witness back up sight, in addition to the LED dot and pistol equipped iron sight. For non-optics ready pistols that need to use an optic plateadapter to replace the pistol manufacturer equipped rear sight, ADE Spike's rear white dot will act as a pistol factory original rear sight for Co-Witness.. Comes with screws for several Optics Ready handguns. Does not comes with any mounting plate such as picatinny mount or plate made for a specific handgun.. Comes with 3 pairs of screws for Sig P365XLX, Springfield Hellcat OSP and Canik TP9 Elite SC ONLY. The provided screws might NOT work with EVERY compatible pistol listed. ADE makes the red dot to accept the industrial standard footprint. The pistol manufacturer makes the optic cutslide for the same footprint, but they have their own opinions to decide which type screws that the screw holes take.. ADE Does not know the screw spec every pistol manufacture used for their screw hole. Please ask the pistol manufacture what screw specs they used on the hole and ask them to provide the screw. If you cant get the screw to work properly, we recommend going to a local hardware store such as ACE Hardware to get the right size..

Proofs impact resistant. Reticle 6 MOA dot. Series reflex sight. Wind age elevation 120 MOA.

Compatible with Non MOS Glock Holosun 507K,Shield RMSRMSC,Sig Sauer Romeo Zero.. Precision CNC Machined from 6AL4V aerospace grade Titanium with black finish.. Update to 30MOA design, Solved some red dots don't have enough elevation adjustment to put the sight down on pistol mount.no more need shim Installation hardware and tools included.. Ultra Low Profile and lightweight, Easy to install.One Piece Design for a Secure Zero Hold.. 100 MONEY-BACK warranty within 30 days of purchaseNO QUESTIONS ASKED. LIFETIME WARRANTY.