Top 10 Best Amprobe Multimeter

Voltage up too 600V ACDC, ACDC current, resistance and frequency. True-rms feature to accurately measure voltage and current in all conditions, including noisy environments affected by harmonics. Capacitance for start-up and run capacitors. Audible continuity, non-contact voltage detection and built-in flashlight. Diode test and duty cycle for troubleshooting applications.

Digital multimeter measures alternating current AC and direct current DC to 2 amp, AC voltage to 1,000 volts V, DC voltage to 1,500V, and resistance to 20 megaohms. Average-sensing meter provides accurate readings when measuring linear loads where the current or voltage has a sinusoidal waveform. Comes with one set of high-voltage test leads and two threaded alligator clips for connecting to high-voltage conductors. Molded plastic case helps protect meter from fire, chemicals, grease, falls, impacts, and abrasions, and is sealed to prevent water and dirt from entering the case. Meets International Electrotechnical Commission IEC safety standard 61010 and is certified for Category IV installations up to 1,000V. Resistance Ranges 200 , 2 k, 20 k, 200 k, 2 M, 20 M. Display 3-12 digit LCD, 1999 counts, with annunciators. Magne-Grip holster, frees both hands for work. Meets EN 61010-1 CAT IV 1000 V 1500 V DC max Class II, EN 60529IP67. Includes high voltage test leads with threaded alligator clips.

ACDC Voltage up to 1000V, acdc current. Resistance, frequency, capacitance. Temperature, duty cycle. True RMS. Low Z - to detect stray voltages.

Digital multimeter measures alternating current AC voltage and direct current DC voltage to 600 volts V, resistance to 6 megaohms, capacitance to 2,000 microfarads, frequency to 30 kilohertz kHz, and AC and DC microcurrent to 2,000 microamp. Average-sensing meter provides accurate readings when measuring linear loads where the current or voltage has a sinusoidal waveform. Non-contact voltage detector senses AC voltage without making contact with the circuit. Meter measures 4.4 x 2.1 x 0.4 inches H x W x D and can be carried in a shirt pocket when not in use. Meets International Electrotechnical Commission IEC safety standard 61010 and is certified for category II installations up to 600V and category III installations up to 300V. Safety CAT II 600 V,CAT III 300 V,Pollution Degree 2, Class 2. AutoTect feature directs the meter to know if it is measuring ac or dc volts or resistance with no user interface. The AutoTect feature has lower input impedance which zeros out ghost voltages. Voltect feature is a built-in, non-contact voltage detector. Automatic Power Off.

Digital clamp meter measures alternating current AC to 600 amp, direct current DC voltage and AC voltage to 600 volts V, capacitance to 3,000 microfarads, resistance to 40 megaohms, and frequency to 100 kilohertz. Average-sensing meter provides accurate readings when measuring linear loads, where the current or voltage has a sinusoidal waveform. Transformer clamp with 1 26 mm jaw opening has jaws that are slimmer than standard clamp jaws, for improved access to tight areas, and measures current without touching or interrupting the circuit. A relative zero mode stores a reading in memory to use as a zero point for subsequent readings. Meets International Electrotechnical Commission IEC safety standard 61010 and is certified for category III installations up to 600V. Rubber over-molded case. Hold and maximum reading functions. Capacitance to 3000 uF. Meets EN61010-2-032, UL61010B-2-032, IEC61010-1 2nd Ed., EN61010-1 2nd Ed., UL61010-1 2nd Ed. CAT III-600 Volts ac dc. Pollution degree 2.

Inductance To 40 H, Frequency To 40 MHz, Capacitance To 400 microF, Logic To 20 MHz. Input Warning Tone When Test Leads Are In Wrong Jack. 10,000 Count, 0.1 Accuracy. 1000V750V DCAC True RMS. 10 Amps ACDC, Fully Safety Fused -- Resistance To 40Mohm.

Integrated tilt stand for easy bench use. Diode test for component level troubleshooting. Data Hold freezes display to hold measurement reading. 750 V AC 1000 V DChighest voltage rating in this size of meter. Special 2000M Ohm measurement range.

Display voltage and amps concurrently with large LCD dual display. True-RMS for accurate voltage measurements in noisy environments. Low pass filter for current and voltage measurements on variable frequency drives. Precise low current measurement down to 0.1 amp. HVAC applications with temperature, DC micro-amps and capacitance.

Tests capacitance, resistance, and inductance, and checks transistors and diodes to verify functionality and compatibility of electrical circuits and devices. Zero-adjust pots help eliminate stray capacitance, resistance, and inductance for more accurate readings. Comes with a set of detachable test leads with test probe tips and two alligator clips for a more secure, hands-free connection than probe tips. Diode and transistor test checks for proper functioning of the circuit's diodes and transistors, including microwave diodes. Audible continuity buzzer confirms that a circuit is capable of conducting current. The ultimate component checker measures inductance, capacitance, resistance, transistors, diodes and microwave diodes. Plug-in test slots and test leads with threaded alligator clips. Oversized, digital display. Data hold, Max hold, Zero adjust pot for Ohms, Low battery indication, Auto-power off.

True-rms for accurate measurements on non-linear loads. safety rated. Large white LED Backlight to work in poorly lit areas. Operating Temperature -10 C to 50 C Storage Temperature -40 C to 60 C. Check continuity, frequency, capacitance and diode test. Measures 20 A 30 seconds momentary 10 A continuous. True-RMS for accurate measurements on non-linear loads. CAT III 600 V safety rated. Large white LED backlight to work in poorly lit areas.