Top 10 Best Amps Car Audio

Power - 3000 Watts Max x 1 1-Ohm, 1500 Watts Max x 1 2-Ohms. Class D - Power loss is significantly reduced making the amplifier highly efficient. Excess energy is stored until its needed instead of being converted into heat. Reduction in sizeweight, reduced power waste, smaller heat sink, compact circuitry. 1 Ohm Stable - Able to continuously power loads of 1 Ohm without encountering difficulties such as overheating. Typically made to power up subwoofers that demand the heavier power load requirements to be able to perform the way they were made to. Strapping Capable - You are able to strap TWO PL3000.1D amplifiers and double the power that is being sent to your subwoofers. You now have the ability to connect more subwoofers to take advantage of the extra power. Variable Subsonic Filter - To prevent your subwoofers from bottoming out, the variable subsonic filter filters out frequencies below the subwoofers specified low frequency limits and allows the driver to reach a maximum safe excursion. Variable Low-Pass Crossover - Subwoofers reproduce sound based on a number of different low-range frequencies. You can set exact sound specifications for the bass frequency reproduction. Variable Bass Boost - Bass Boost allows you to adjust the low bass within the boost range to just the way you like it. Specs - Dimensions 11.9 x 7 x 2.3, Weight 6.7 lbs..

Class D MOSFET Monoblock Power Amplifier. Peak Power at 1 Ohm 1,600 Watts RMS Power at 1 Ohm 1,200 Watts. Frequency Response 20Hz - 250Hz, On-board Bass EQ Switch with 6 or 12dB boost at 45Hz. Featuring 4-Way Protection Circuitry and 4 Gauge Power Ground Input Terminals for Maximum Current Flow. Damping Factor - 150. Stable at 1 ohm Remote Subwoofer Level Control Included. Highly Efficient Heatsink Design allows for Maximum Reliability Performance.

4-CHANNEL AMPLIFIER 4-channel amplifier can put out 65 watts per channel to enhance your music and get a boost in volume and clarity Hardware is included that allows you to easily mount vertically. SMOOTH SOUND Separate high and low pass filters on the front and rear channels help you sculpt the sound to get the most out of all your speakers. LOW-END BASS PUNCH Variable bass boosts can allow you to add some low-end punch Amplifier is free from noise or interference so that you can tap into your speaker wiring without any worry. QUICK TURN ONOFF Quick 3-second turn onoff delay eliminates system pops. SPECIFICATION 65 watts RMS x 4 at 4 ohms 180 watts RMS x 2 bridged at 4 ohms Class AB Amplifier Frequency response 10-20,000 Hz Variable bass boost 0-6 dB at 40 Hz.

Class AB full-range channels. Class D bass channel included for one amp to run an entire system. Three-second turn-onoff delay to eliminate unwanted interference. Variable 12dB crossovers provides control to dial in perfect sound. KickEQ 6dB variable bass boost for those additional low frequencies.

POWER 3000 Watts Max x 1 1-Ohm, 1500 Watts Max x 1 2-Ohms. DIMENSIONS The OX3KD is 12.3 inches in Depth, 7 inches in Width and 2.3 inches in Height. It weighs 6.5 lbs.. CLASS D Power loss is significantly reduced making the amplifier highly efficient. Excess energy is stored until its needed instead of being converted into heat. Reduction in sizeweight, reduced power waste, smaller heat sink, compact circuitry. 1 OHM STABLE Able to continuously power loads of 1 Ohm without encountering difficulties such as overheating. Typically made to power up subwoofers that demand the heavier power load requirements to be able to perform the way they were made to. STRAPPING CAPABLE You are able to strap TWO OX3KD amplifiers and double the power that is being sent to your subwoofers. You now have the ability to connect more subwoofers to take advantage of the extra power. WARRANTY BOSS Audio Systems provides a powerful 6 year Platinum Online Dealer Warranty so long as the purchase is made through Amazon.Com. We strongly encourage professional installation of this product to ensure proper and safe functionality.

Subwoofer amplifier with patented AccuBASS. 800 watts 2 ohms --- 500 watts 4 ohms. AccuBASS Processing. MILC Maximum Input Level Control Patent Pending --- GTO Signal Sense. 24 dBoctave Linkwitz-Riley Alignment crossover -- Speaker level and preamp inputs.

Wiring Kit - 30 Ft Speaker Wire, 20 ft. 8 GA Red Power Cable, 16 ft. 18 GA Blue Turn-On Wire, 3 ft. 8 GA Black Ground Cable, Competition Quality Fuse Holder with AGU Fuse. Wiring Kit Continued - 10 516 and 14 Ring Terminals, 6 ft. Split Loom Tubing, 3 Rubber Grommets, 20 4 Wire Ties, 20 ft. High Performance blue RCA TRCA Interconnect. Amplifier Power - 1100 Watts Max x 1 2-Ohms, 550 Watts Max x 1 4-Ohms. Class AB Topology - Class A amplifiers have enormous amount of current flowing through its output transistors with no audio signal. Class B amplifiers have no current flowing through its outputs with no audio signal. Mosfet Power Supply - A MOSFET is an electrical switch that allows the flow of electrical current. It controls the output voltage and current precisely by removing the output current sensing loss eliminating all secondary feedback circuitry. Variable Low-Pass Crossover - Subwoofers reproduce sound based on a number of different low-range frequencies. You can set exact sound specifications for the bass frequency reproduction. Switchable Bass Boost - Bass Boost allows you to adjust the low bass within the boost range to just the way you like it. Specs - Dimensions 9.1 x 10.4 x 2.3, Weight 4.4 lbs.. Warranty - BOSS Audio Systems provides a Powerful 6 Year Platinum Online Dealer Warranty so long as the purchase is made through Amazon.Com. We strongly encourage professional installation of this product to ensure proper and safe functionality.

AUDIO EVOLUTION This amplifier car audio features excellent frequency response rates and crossover network that place these amps in a class of their own.. SOUND SPECIALIZATION This high-powered Power Amplifier is cutting edge technology at its finest. RCA connectors ensure a secure connection between amplifier and speakers that allow distortion-free sound.. INTELLIGENT DESIGN The amplifier monoblock features include power and protection LED indicators soft turn-onoff and 1 channel amp design.. RCA JACKS The Line-Out jacks allow you to build multiple amplifier systems without having to use splitter cords to distribute the signal. This makes it easier to bring one set into the first amp, then use the line out jack as the feed to the next amp.. GREAT DEAL Often a monoblock amp comes with a high price tag. Yet the Lanzar mono amplifier is budget friendly with all the features, reducing crosstalk between channels. Please update the listing's title, description, bullets..

The BXX1200.1D is a 1200 watt mono amplifier featuring Super Class D technology with an NGSD digital chip to provide you with an extremely efficient, low temperature, high amplification system that others only dream about.. The rock solid Ultra-Fi MOSFET outputs are selected for both balance and output power. This keeps power smooth even during demanding peak in the music.. The amplifiers protection condition is also shown by blue illumination for normal operation and red for a short being present and requires the attention of an installer.. Max Power Rating 4 ohms 400 watts x 1 chan. 2 ohms 600 watts x 1 chan. 1 ohm 1200 watts x 1 chan.. Dimensions 9W x 13.25L x 2.5H, 1-year Manufacturer's Warranty.

Efficient Class-D amplifier. Variable 12dB crossovers provides control to dial in perfect sound. KickEQ 6dB variable bass boost for those additional low frequencies. Variable 12dB crossovers provides control to dial in perfect sound. 24dB subsonic filter for protection from potentially damaging frequencies.