Top 10 Best Arduino Motor

This is a good parts kit for RC car project. It not only comes with 4pcs wheels and motors, but also 2pcs motor drive modules and 60pcs jumper wires, which are very useful accessories for your project.. Motor Drive Controller L298N used as the main driver chip. It has the strong driving ability, low calorific value and strong anti-interference ability.. TT Motor The motor is a two-axis motor with a reduction ratio of 148, which has strong anti-interference ability.. Smart Car Wheels The wheels are made of high-strength plastic and the tires are made of durable black rubber.. To avoid damage the voltage stabilizing chip of Motor Drive Module, please use an external 5V logic supply when using more than 12V driving voltage..

Type 130 Mini DC Motors for 1.5V to 6V, 3V is recommended. Come with 6 inch 15cm black and red wire leads for easy connection. Motor size 15 x 20 mm, Shaft diameter 2.0 mm, Shaft length 9 mm. Reference current 0.35-0.4A, Speed 16000 RPM at 3V. Perfect for robotics projects, solarbattery-powered cars, brush-bots, fanswindmills, and more..

SG90 9G micro servo motor for remote control helicopters, micro robot, robot arm and boats. Fit for ALL kinds of RC Toys and also make electronics DIY compatible with Arduino, Raspberry Pi. Interface Type Compatible with JR FUTABA interface. Running Speed at no load 0.09 0.01 sec604.8V 0.08 0.01 sec606V. Running angle 180 degree. Stall Torque 4.8V 17.5oz in 1kgcm. Dead band setting 5 ms. Amplifier Type Analog controller. Operating Voltage 4.8V6.0V. Please Note The starting current of the motor should be greater than 1A. Comes with 1 year warranty and lifetime technical Support.

Control speed and direction for two DC motors, or just speed with four DC motors drive a large stepper motor up to NEMA 17.. Connect other sensors and actuators through the shields Molex connectors.. Connect more to your board It works also for up to four external relays or solenoids.. Works with your Arduino Uno, Uno SMD, Mega, and Leonardo.. External power input to separate the motor power from the microcontroller one..

TT DC Gearbox Motor Rated Voltage 3-6VGear Ratio 148Wires Length 200mm 28 AWGStall Torque 6V 0.8kg.cm. High Quality Motor Set made of Premium Environment Friendly Materials, Durable and Longer Wheel and Motors Service Life. Easy to Install TT DC Gearbox Motor Comes With 2x 200mm Wires ConnectorMale 2.54mm, Easy to Plug into a Breadboard or Terminal Blocks. Application This TT DC Gearbox Motor Set Can Use for DIY Smart Robot, Car Projects,Distance Measurement, Velocity, Educational Learning, Smart Robot Car Competition and Entertainment etc. Package Contents You will get 8pcs TT DC Gearbox Motor and 4pcs Wheel ,Perfect for DIY Car Projects and Smart Robot.

This is a TT DC Gearbox Motor with a gear ratio of 148, and it comes with 2 x 200mm 28AWG wires with breadboard-friendly 2.54mm0.1 male connectors. Perfect for plugging into a breadboard or terminal blocks. Rated Voltage 36V, Continuous No-Load Current 150mA - 10. Min. Operating Speed 3V 90- 10 RPM, Min. Operating Speed 6V 200- 10 RPM. Torque 0.15Nm 0.60Nm, Stall Torque 6V 0.8kg.cm, Gear Ratio 148. What you will get is 4 X TT motors with welded cable, 4 X wheels.

Stepper motor with a standard interface, when used directly pluggable.. A, B, C, D four-phase LED indicates the status of the stepper motor work.. 5 line 4 phase can be used for ordinary ULN2003 chip driver, connect to the 2 phase , support the development boardWith convenient use, direct docking. Drive Module Board Sizein 1.371.180.6 Stepper Motor diameter 1.06in Stepper Motor lines 9.45in. Great packing in a box 5 set Uln2003 Stepper Motor Driver Board with a little gift.

Application Fields remote control helicopters, micro robot, robot arm and boats. ALL kind of RC Toys and Arduino experiments. Interface Type compatible with JR Futaba interface.. No Load Running Speed 0.090.01 sec60 at 4.8V Rotary Angle 120. Stall Torque 4.8V 17.5oz in 1kgcm.Dead band width 7usec. Amplifier typeAnalog controller Operating voltage 4.8V6.0V.

Latest CH340G CNC Shield expansion board Version 3. 0 for Arduino. Kuman Board, MCU ATmega328, USB interface ATmega16U2 with 1. 5m USB Cable. 4pcs DRV8825 Stepper Motor Driver with heat sinks. 3pcs NEMA-17 Stepper Motor 84 oz. in 59 Ncm 47mm Body 1. 8 degree with mounting Bracket Kit DIY CNC Robot with 3pcs Mounting Bracket and 12 pcs M3 Screws. 3pcs End stop Mechanical Limit Switches for RAMPS 1. 4 with 3Pin 70cm Cable.

8PCS TT DC Gearbox Motor with a gear ratio of 148.. Comes with 28AWG wires 2.54mm0.1 male connectors, perfect for plugging into a breadboard or terminal blocks.. With EMC, it has strong anti-interference ability and causes no interference to micro-controller.. Rated Voltage 36V.. Great for RC car DIY or other electronic production..