Top 10 Best Arduino Transmitter And Receiver

Easy to use, nice range using antenna on both, you can send strings text from one point to another. If you want to automate your house without pulling cables then this device will help you well. Wireless Transmitter Modules allow your Arduino to wirelessly comunicate with other arduinos, or with radio frequency RF controlled devices that operate in the same frequency 433Mhz in this case. They work in pairs, meaning you need both a receiver and a transmitter to comunicate with each other. Compatible with SparkFuns 434MHz RF transmitter and RF receiver. This Radio Transmitter Receiver pair is perfectly matched to allow you to control items from a distance up to 500 feet wirelessly.

Easy to use, nice range using antenna on both, you can send strings text from one point to another. If you want to automate your house without pulling cables then this device will help you well. Wireless Transmitter Modules allow your Arduino to wirelessly comunicate with other arduinos, or with radio frequency RF controlled devices that operate in the same frequency 433Mhz in this case. They work in pairs, meaning you need both a receiver and a transmitter to comunicate with each other. Compatible with SparkFuns 434MHz RF transmitter and RF receiver. This Radio Transmitter Receiver pair is perfectly matched to allow you to control items from a distance up to 500 feet wirelessly.

Note The white smudge is not corrosion damage, it's flux, can wipe it off with a rag, does not affect the use of the module. This ir transmitter sensor module is directly launched by a single tube, it requires waveform modulation through the program.. It is suitable for infrared communication, infrared remote control, apply to a variety of platforms including Arduino51AVRARM. With signal indicating LED, easy to observe and debug.. Pin Definitions 1 Output 2 Vcc 3 GND.

Maximum operating speeds up to 2Mbps, GFSK modulation efficiency, Anti-interference ability, Particularly suitable for industrial control applications.. 125 Communications channels, Multi-point communication and frequency hopping to meet the communication needs.. Built-in hardware CRC error detection, Multipoint communication address control. Built-in 2.4Ghz antenna.. nRF24L01 is a single chip radio transceiver for the worldwide 2.4 - 2.5 GHz ISM band. Compatible with Arduino and Raspberry Pi.. Applications wireless peripherals, remote control systems such as RC vehicles and consumer remote electronics, wireless voice transmission such as VoIP, wireless sensor networks, wireless networks, home and commercial automation..

IR is widely used in remote control. With this IR receiver, the Arduino project is able to receive command from any IR remoter controller if you have the right decoder.. It will be also easy to make your own IR controller using IR transmitter.. With 1838 remote control receiver, the sensitivity is high.. Operating voltage 5V, digital output, with data indicator.. 2 fixing holes for easy installation, aperture 3.1mm, PCB size 23.521.5mm..

This Ir transmitter sensor module is directly launched by a single tube. It requires waveform modulation through the program. Pin Definitions 1 Output 2 Vcc 3 GND. Attention The white smudge is not corrosion damage, it's flux, can wipe it off with a rag, does not affect the use of the module. Widely used for infrared communication, infrared remote control, apply to a variety of platforms including 51AVRARMWith signal indicating LED, easy to observe and debug..

Operating voltage 5V. Source wavelength 650 nm. Apply to for Arduino AVR. Model 1Laser Receiver Sensor Module 1 KY-008 Laser Transmitter Module. Laser Receiver Sensor Module uses the non modulated laser receiver, please use in the room where without the light, the sunlight or other lamps and lanterns will interfere, suggested in the dark environment use..

RXB6 433MHz Superheterodyne Wireless Receiver Module. receiver sensitivity reach -116dBm. Operating frequency433.92 MHz. Power supply voltage input range 3V-5.5V. Low power consumption, 3.3V 433.92MHz, 6.0mA.

Test mode Using IO trigger for high level signal. Not less that 10us,The Module sends eight 40 kHz automatically and detect whether there is a pulse signal back.. The detection zone 0.78196 in 2cm500cm High precision up to 0.12 in0.3 cm Effectual angle less than 15.. Power supply 5V DC Quiescent current less than 2mA.. Test distance Duration of high levelSonic 340ms2.. Package included 5 x HC-SR04 Ultrasonic Module..

Based on the 38KHz IR Receiver Sensor. 1pcs 38KHz IR Receiver Sensor and 1pcs 38KHz IR Transmitter Sensor. Can be used for remoter control,Can be compatible with Wrobot Digital 38KHz IR Transmitter Sensor. Power Supply 5V. Modulate Frequency 38Khz.