Top 10 Best Bending Tool

Three sizes of sheet metal bending pliers for your selection straight jaw, 45 degree jaw, 90 degree jaw. These hand seamers are 2-38'' 60mm wide.. Designed for bending or straightening sheet metal edge. Ideal tool for use on the car when it is not possible to use a bench folding machine or in tight areas.. Made of high quality, heat treated drop forged carbon steel, these tools are made with longevity and durability. Hardness approx. 30 to 35 HRC. Complete with a black finish with red dipped handles.. The pliers jaw close perfectly parallel and the edges of the pliers head are very straightbut they are not sharp. Sheet metal is not damaged when bending through the jaws of the pliers.. Please note the metal benders may being a bit stiff to openclose at first, but they will start to loosen up after a while..

Sheet Metal Folding ToolHurricane 18 sheet metal folding tools offer a premium choice for bending and forming metal, folding seams are formed from 2 steel halves, permanently joined together.. Two Folding DepthsCreates 38 and 1 depth folding in ductwork.. Ideal for HVAC ApplicationsUsed for bending and forming metal, making seams, hems, pans and drive edges.. Ensures Precise and Accurate BendsHandy sight holes assure accurate bending depth alignment.. Constructed of Heavy 16-Gauge SteelPowder-coated low carbon steel to resist rust..

6-7S Ultra-Fast Bending Speed This electric rebar bender is designed with excellent performance. It helps save valuable person-hours by bending rebar 14'' 2 to 1 8 Grade 606 to 25 mm within 6 to 7 seconds. Bending Angle 0-180, Bending Radius 1.57'' 40 mm, Max. Rebar Hardness HRC30, Item DimensionsL x W x H 17.72'' x 19.69 x 20.08'' 45 x 50 x 51 cm.. 1700W Pure Copper Coil Motor This hydraulic bending machine features a 1700W pure copper motor, which can run quietly with low noise and significantly improve your working efficiency, reducing unnecessary wear. Besides, a copper motor can extend this electric rebar machine's operating life to a large extent. Voltage 110V, Frequency 60 Hz, Amps 14A, Noise 92 dBA.. Angle Adjustment Knobs This rebar bending machine has two slide-type angle selectors, which can help you accurately bend any angle from 0-180 degrees. Preset angle locks are designed for repeating the same angle bending. When bending processing, the angle of point 1 must be bigger than point 2. Otherwise, the machine can not operate normally.. Sturdy Machine Body The electric bender machine adopts a sturdy iron machine body and durable Idler Wheel. 78 iron Gyre Idler Wheel and 94 Fixed Idler Wheel are stronger and not easy to break. Moreover, it can stand super-hard rebar with strong clamping force, which can help to reduce steel rebar waste.. Easy to Operate Transport This hydraulic rebar bender comes with the standard foot pedal control switch for your easy hands-free bending. With four handles on the corner for you to transport and operate effortlessly. It is widely used in construction engineering for bending rebar, steel bar, steel rod, screw thread steel, carbon steel, round steel, etc..

6-7S Ultra-Fast Bending Speed This electric rebar bender is designed with excellent performance. It helps save valuable person-hours by bending rebar 14'' 2 to 1-14 10 Grade 606 to 32 mm within 6 to 7 seconds. Bending Angle 0-180,Bending Radius 1.97'' 50 mm, Max. Rebar Hardness HRC30.. 3000W Pure Copper Coil Motor This portable rebar bender features a 3000W pure copper motor, which can run quietly with low noise and significantly improve your working efficiency, reducing unnecessary wear. Besides, a copper motor can extend this electric rebar machine's operating life to a large extent. Voltage 110V, Frequency 60 Hz, Amps 26A, Noise 105 dBA.. Angle Adjustment Knobs This rebar bending machine has two slide-type angle selectors, which can help you accurately bend any angle from 0-180 degrees. Preset angle locks are designed for repeating the same angle bending. When operating under point 2, fix angle of point 2 same as or no larger than point 1 of 5 degree, to ensure that under the condition when exterior shock attacks the machine itself will not move to left and right to operate the machine.. Sturdy Machine Body The electric bender machine adopts a sturdy iron machine body and durable Idler Wheel. 78 109 Fixed Idler Wheel and 99 148 Gyre Idler Wheel are stronger and not easy to break. Moreover, it can stand super-hard rebar with strong clamping force, which can help to reduce steel rebar waste.. Easy to Operate Transport This hydraulic rebar bender comes with the standard foot pedal control switch for your easy hands-free bending. With four handles on the corner for you to transport and operate effortlessly. It is widely used in construction engineering for bending rebar, steel bar, steel rod, screw thread steel, carbon steel, round steel, etc..

ApplicationDurable hardened bending tool designed to bend soft copper, aluminum, coated soft copper, widely used in sanitary and heating installations, floor heating, refrigeration and air-conditioning, hydraulic systems.. Kit IncludedTubing Bender x 1, Fixed Supports x 2, Tube Bender Heads x 7, Reverse Bending Tool x 1, Pipe Cutter x 1, Inner Outer Reamer x 1, Pipe Reamer x 1, Carrying Box x 1, Manual x 1.. Ergonomic DesignAlumium alloy replacemnt bender heads prevent pipe deformation, solid and durable. Extra-long handles increase leverage while swaging, reduce force needed. Pipe cutter with a deburring tool for cleaning tubes.7 exchangeable tube bender heads, professional tool for use.. Suitable Size7 Elbow diameter range for pipes 14, 516, 38, 12, 58, 34, 78 inch 6,8,10,12,16,19,22mm O.D. tubing cutter capacity316 to 1-14-inch 4-32mm.. Special Reverse Bender FunctionReverse bending tool helps bending pipes in both forward and reverse configurations, allows it to fit where others can't. Blow molded hard plastic storage case keeps tools contained and organized, provides a convenient handle for easy transportation and portability. User manual for easy use..

Lightning-Fast Performance The rebar bending and cutting machine boasts exceptional performance, bending rebar from 14'' 2 to 1 8 Grade 60 6 to 25 mm within 6 to 7 seconds and cutting rebar within 5-6 seconds. It can bend at any angle from 0-180 with a bending radius of 1.57'' 40 mm, and its maximum rebar hardness is HRC30. The hydraulic oil type used is VG46.. Powerful 1600W Copper Coil Motor Equipped with a 1700W pure copper motor, this rebar cutter and bender runs quietly, has low noise and improves working efficiency, reducing unnecessary wear. The copper motor extends the operating life of the machine. It operates at a voltage of 110V, frequency of 60 Hz, with amps of 14A, and noise level of 92 dBA.. Angle Adjustment Made Easy The rebar bending machine has two slide-type angle selectors, making it easy to bend any angle from 0-180 degrees. Preset angle locks ensure accurate, repeatable angle bending. During bending, the angle of point 1 must be greater than point 2 for proper operation.. Durable Construction This bar bender machine has a sturdy iron machine body and durable Idler Wheel. The 78 iron Gyre Idler Wheel and 94 Fixed Idler Wheel are strong and unlikely to break. It can handle super-hard rebar with strong clamping force, reducing steel rebar waste.. Easy to Use and Transport The heavy-duty rebar cutter bender comes with a standard foot pedal control switch for hands-free bending. Four handles on the corners make it easy to transport and operate. It is widely used in construction engineering for bending or cutting rebar, steel bar, steel rod, screw thread steel, carbon steel, round steel, etc..

Risk-free shopping What you buy is not only bead roller tool for sheet metal, but also our complete after-sales service you trust me, I will give you a satisfactory experience. If you are not satisfied, you can contact us at any time, and we will reply to you within 12 hours to solve your problem.. Easy to adjust the angle The sheet metal edge roller bender is used for cleaning and bending of metal roofing panels such as steelaluminumcopper, etc., and manufacturing 0-90 bending of 58 to 4 16 to 102 mm in No. 29 to 22 0.36 to 0.76 mm steel. The unique three-position crimping roller design can produce uniform bending. The center roll can be adjusted independently to make elbows, as shown in the bottom of Figure 3.. Perfect upgrade advantagesThe three-station edge roller is upgraded from a cylindrical pulley to a V-shaped roller, which can clamp the material perfectly when making bending materials, reduce the error in the bending process, and solve the problem of easy sliding and error in the manufacturing process. This upgrade has greatly improved the problem of chicken ribs in the process of sheet metal edge roller bender use, and is our proud masterpiece,see Figure 4 for details.. High quality structureThe sheet metal roller bender With the upgraded aluminum alloy handle, our sheet metal bending machine provides you with a comfortable grip, which saves your strength and makes it easier to move. Six solid steel columns, upgraded solid structure, high hardness and durability. The connection between the solid steel column and the machine is made of high-quality brass with high strength, which is not easy to deform and rust. The three safe and stable screws are easy to adjust, and the height can be adjusted only by twisting, and the design of three numbers makes the sheet metal bender firmly fixed in place.. Accurate depth gauge there is an accurate inchmetric depth gauge on one leg of the central roll station of the metal bender . When locked in the desired position, you can accurately align the depth of all roller stations, and then obtain the desired exact bending size..

0 - 90 Degrees Excellent Performance This electric rebar bender is designed with excellent performance. It helps save valuable person-hours by bending rebar 14'' to 1 6 to 25 mm within 5 seconds. 14'' 6 mm 2 Rebar0-55, 1'' 25 mm 8 Rebar0-90. It is able to satisfy your various bending demands.. 1500W Pure Copper Coil Motor This portable rebar bender features a 1500W pure copper coil motor, which can run quietly with low noise and significantly improve your working efficiency, reducing unnecessary wear. Besides, a copper motor can extend this rebar bending machine's operating life to a large extent.. Sturdy Machine Body Head The electric bender machine adopts the sturdy machine body and high-intensity hook, which are stronger and not easy to break. It can stand super-hard rebar with strong clamping force, which can help to reduce steel rebar waste. Multiple screws fixed on the head enforce the stability and sealing.. Precision Pressure Relief Valve This hydraulic rebar bender features a precision pressure relief valve and a hydraulic-powered piston for strong thrust and less power consumption. After the steel bar is successfully bent, you can pull the pressure relief valve to move the steel, and the piston will return to its original position.. One Button Operation This electric rebar machine is equipped with an ergonomic back grip design to facilitate maneuverability and ease of use. Simply keeping the switch pressed, the bending block starts to push forward. It is easy to bend rebar even in high air and is widely used in construction engineering for bending rebar, steel bar, steel rod, screw thread steel, carbon steel, round steel, etc..

Powerful 1200W Pure Copper MotorWith the electric hydraulic-powered motor and piston, Anbull rebar bender makes each bend both fast and efficient , and it also features strong thrust with less power consumption and lower noise.. Great Bending and Straightening Capacity Anbull RB22 concrect rebar bender has powerfull push and pull capabilities which allows bending or straightening 78 22mm rebar to 90 or greater within 5 seconds, satisfying your various manufacturing needs. Note The rebar straightening head is not included in the Rebar Bender and needs to be purchased separately. Please refer to ASIN B097MHZYJP. Three-point BendingThe electric rebar bending machine Designed with a piston that moves forward forming a three-point bending system for the rebar bending head, the bending can be made fast and efficient.. One Button OperationWith its compact and portable design, it can be easily carried by one person for effective on site construction, and it runs on the standard 110V outlet, perfect for all rebar projects both at workplace and on the job site.. Precision Quench Technology Equipped with a pressure relief valve to release the power after bending, our electric hydraulic rebar bender comes with a bending block quenched with precision steel casting technology..

Satisfactory Service We provides THREE-YEAR FACTORY WARRANTY. Suitable Tube Size 14, 516, 38, 12, 58, 34, 78, the maximum bending angle of elbow pipes 90 degrees, support reverse bend. bending pipes in both forward and reverse configurations.. Made of 40CR steel and 45 steel. Suitable for bending annealed metal materials or PVC pipes, such as thin-walled steel pipes thickness0.05 inch, aluminum pipes thickness0.08inch, soft copper thickness0.08inch.. With pipe cutter, suitable for cutting heavy and hard materials, such as thin stainless steel thickness0.05 inch, all hoses, such as aluminum thickness0.08inch, copper thickness0.08inch and PVC.. Application automobile maintenance, refrigerator maintenance, Hvac work, hydraulic system, etc.. Package Include Tubing Bender x 1, Fixed Supports x 2, Tube Bender Heads x 7, Reverse Bending Tool x 1, Pipe Cutter x 1, Deburring Tool x 1, Carrying Box x 1, Manual x 1.

MANUAL TUBING AND PIPE BENDER manufactured with high-quality, heavy duty steel, this tube bender will efficiently bend copper, brass, aluminum and thin steel pipes. This pipe bender provides a fast, economical way to produce angled bends in round tubing. VERSATILE PIPE BENDER FOR ALL INDUSTRIES this copper pipe bender is suitable for use on construction sites, plumbing jobs, shipping, manufacturing, heating, decorating or even at garage repair shops. EASY TO OPERATE the Loreso manual pipe bender is easy to operate and portable so you can take it from site to site. Made with high precision and premium machining quality, it is a robust tool that is built to last. VARIOUS DEGREES AVAILABLE simply adjust the metal bender according to the angle you require from 0-180 degrees. This pipe bender is a 3 in 1 tool and will fit 14, 516, 38 8, 6, 10mm tubing. STURDY CAST ALUMINUM FRAME our copper tube bender is made from strong, durable cast aluminum and can be mounted on either a bench or frame the safest way to bend tubes, conduit and pipes quickly and effectively.