Top 10 Best Fluke 787

20 ma dc current sourceloop calibratorsimulator. Dmm designed to meet 1000 volt iec 1010 cat iii. Precision 1000 v, 440 ma true-rms digital multimeter. 100 larger dual display than the 787 ProcesssMeter.

1000v overload protection on v, ohms, frequency, and 150v overload protection on ma, backed up by a 440 ma 1000v fuse. Runs about 50 hours typical measurement, 12 hours typical sourcing 12 ma on one 9 volt alkaline battery. 25 percent manual step plus auto step and auto ramp on ma output. Simulate dc loop current with .05 percent accuracy and 1 micro amp resolution. Runs about 50 hours typical measurement, 12 hours typical sourcing 12 ma on one 9 volt alkaline battery. Clear LCD display with backlight.

Your unit is calibrated prior to shipment with a new nist-traceable calibration Certificate with data. The NIST calibration provides you assurance your instrument Meets manufacturers specifications. Your instrument is ready to Use day one meeting most quality system standards. 1000V overload protection on V, Ohms, frequency, and 150V overload protection on mA, backed up by a 440 mA 1000V fuse. Runs about 50 hours typical measurement, 12 hours typical sourcing 12 mA on one 9-volt alkaline battery. Clear LCD display with Backlight.

PI polarity index DAR dielectric absorption ratio with Trend It graphs identifies problems faster. Memory storage through mobile Fluke Connect Measurements App eliminates writing down results, reduces errors and saves data for historical tracking over time. Temperature Compensation through App helps establish accurate baselines and relevant historical comparisons. VFD low pass filter for accurate motor drive measurements Includes auto discharge of capacitive voltage for added user protection. Insulation test voltages 50 V, 100 V, 250 V, 500 V, 1000 V.

3 test leads red, black, green connected to low-leakage probes. 3 alligator clips red, black, green. 2.6m lead length. 26mm maximum jaw opening. Replacement test lead set for the fluke 1550B MegaohmMeter. Silicone-insulated leads have superior flexibility in cold temperatures and resistance to high temperatures. Insulated alligator clip rated up to 5A. Slide-on IC probe tip adapter rated up to 3A and test lead couplers. Bare spade lug with banana connector, rated up to 10A. CAT III 3000-volt, compatible with fluke and other multimeters that accept safety shrouded, standard diameter banana connectors.

Digital clamp-meter for 24V loop circuits measures DC to 100mA via clamp and to 24mA in circuit, and DC voltage to 30V. Meter can source and simulate DC signals from 4 to 20mA, can source DC voltage signals up to 10V, and is accurate to 0.2 with a resolution of 0.01mA. Clamp with 4.5mm 0.177 inches jaw opening measures current without touching or interrupting the circuit, and is for use in hard-to-reach applications. Built-in 24V loop power supply to power a transmitter and measure its milliamp output signal. Meets EN and IEC safety standards 61010-1 and 61010-2-032. Dual backlit display with both mA measurement and percent of 4 to 20 mA span. Measurement spotlight. Measure up to 99.9 mA range non-contact. Automatic power off. 4 to 20 mA scaled output.

1000V overload protection on V, Ohms, frequency, and 150V overload protection on mA, backed up by a 440 mA 1000V fuse. Runs about 50 hours typical measurement, 12 hours typical sourcing 12 mA on one 9-volt alkaline battery. Clear LCD display with Backlight. Current Measurement Range 0 to 30 mA DC. 24V loop power supply. 25-Percent Manual Step plus Auto Step and Auto Ramp on mA output. Built-in, selectable 250-Ohm Hart resistor. 0 and 100-Percent buttons to toggle between four and 20 mA sourcing for a quick span check. Very large dual display with enhanced backlight with 2 brightness settings.

Industrial thermometer combo kit. Full featured DMM with advanced electronic troubleshooting functions plus probes.

More precise measurement and calibration source performance, accuracies of 0. 01 percent. 2 separate channels measure, source and view process signals simultaneously. Measure volts, mA, RTDs, thermocouples, frequency and resistance to test sensors and transmitters. Sourcesimulate volts, mA, thermocouples, RTDs, frequency and pressure to calibrate transmitters Maximum current22 mA, short circuit protected. 3 Year.

Stores up to 15,000 recorded events. Real time clock for automatic time stamping of saved readings. Large 50,000 count, 14 vga display with a white Backlight. Low impedance voltage function prevents false readings due to ghost voltage. Unique logging and graphing capabilities mean you no longer need to download logged readings to a PC to detect a trend. Stores up to 15,000 recorded events.Electromagnetic compatability EMC EN6 1326-1. Real time clock for automatic time stamping of saved readings. Large 50,000 count, 14 VGA display with a white backlight.