Top 10 Best Happymodel

The ES24TX module is a complete solution which is already pre-load the Expresslrs firmware and its plug and play.. MCUESP32main,ESP8285aux,as espbackpack RF chipSX1280IMLTRT JR standard 5pin socket.. The default factory firmware is aec8ad82 which matching EP1 and EP2 RX, You can copy the firmware to the SD card, and then directly update the firmware of the ES24TX on the RC remote control.. The other firmware of ES24TX is to match Happymodel PP RX receiver program version identification code 6cb8152d.. Receiver refresh rate 25Hz - 500Hz RF Output Power 10dBm24dBm Power supply voltage 5V10V Antenna gain1.87dBi..

The lightest 1s 75mm brushless compatible for whoop. Powerful and efficiency Low profile Canopy design. The lightest 1s AIO 5IN1 F4 flight controller. New Unibell EX0802 brushless motors. VTX power switchable 25mw200mw.

The Happymodel 2.4GHz ELRS nano series receiver is an open source program based on ExpressLRS, we have 3 types rx module released.. On the basis of PP RX, we have developed the Nano 2.4GHz rx of ESP8285 version named EP1 and EP2. The RF module of EP1EP2 is the same like PP RX and use ESP8285 MCU . So you can upgrade firmware by WIFI , that's too simple. Due to the low-latency and high-refresh-rate RF module, they are very comfortable for FPV race and Long Range FPV. And very suitable for Tiny whoop because of the ultra light and Nano size..

The Happymodel 2.4GHz ELRS nano series receiver is an open source program based on ExpressLRS, we have 3 types rx module released.. The PP RX is designed by Jye Smith from ExpressLRS development team. Its main hardware architecture is STM32L432KBU6 MCU and SX1280 RF chip. It has a built-in ceramic antenna, which is super light and small in size.. On the basis of PP RX, we have developed the Nano 2.4GHz rx of ESP8285 version named EP1 and EP2. The RF module of EP1EP2 is the same like PP RX and use ESP8285 MCU . So you can upgrade firmware by WIFI , that's too simple .. Due to the low-latency and high-refresh-rate RF module, they are very comfortable for FPV race and Long Range FPV. And very suitable for Tiny whoop because of the ultra light and Nano size..

New 41gram 1-2s brushless Toothpick drone with AIO 4in1 CrazybeeX flight controller,CADDX ANT Camera,new 1202.5 brushless motor,XT30 connector.. Flight controllerMCUSTM32F411CEU6 100MHZ, 512K FLASHSensor MPU-6000SPI connectionBoard size 28.5 28.5MMPower supply 1-2S battery input DC 2.9V-8.7VBuilt-in 5Aeach Blheli S 4in1 ESC Dshot600 ready Built-in Betaflight OSDSPI ControlBuilt-in 5.8G VTXBuilt-in SPI FrskvFlysky receiver or no receiver Built-in 5V 1A BEC.. MotorEX1202.5 KV6400Configuration9N12PStator Diamter12mm Stator Length 2.5mmShaft Diameterdl.5mmDimensionDia.Len014mml 4.5mmWeightg4.4gNo.of CellsUpo1-2S. PropellersGemfan 3018-2 Center Thickness 5.5mm Prop Diameter 76.5mm Center Hole diameter 1.5mm. Onboard 5.8g VTXOutput power 25mw-200mw switchableFrequency 40CH Input voltage 3.3V 5.5VCurrent consumption 300mAtypeFrequency 5.8GHz 5bands 40 channels With Race band Smartaudio ready.

This Micro TX is designed by Happymodel and based on the open source- ExpressLRS which is a very popular low latency and high re-flashed rate RF module for RC Airplane and FPV Racing. Its main hardware architecture is ESP32, ESP8285 and SX1280 RF chip. The ES24TX module is a complete solution which is already pre-load the Expresslrs firmware and its plug and play.. Since the official ExpressLRS perfect program has not been released yet, our pre-installed program is a beta version, because there are too many types of beta version programs , so you can download the out of factory firmware from our website.. There are two kinds out of factory firmware of ES24TX, one is to match Happymodel PP RX receiver program version identification code 6cb8152d and the other is to match Happymodel EP1 and EP2 RX receivers program version identification code aec8ad82, The default factory firmware is aec8ad82 which matching EP1 and EP2 RX. You can copy the firmware to the SD card, and then directly update the firmware of the ES24TX on the RC remote control..

Option Basic Version comes with USB LipoLIHV ChargerStandard Versioncomes with 1S06 6 way LipoLIHV charger. Receiver option Frsky Non-EU version support NON-EU Frsky transmitter D8D16 compatible Flysky version support both AFHDS and AFHDS-2A protocol transmitter DSM2DSMX version support DSM2 and DSMX compatible Spektrum transmitter Frsky EU-LBT version support Frsky EU-LBT firmware transmitter. Mode Name Mobula7 Item Name Happymodel 2S 75mm Brushless Whoop racer drone BNF Wheelbase 75mm. New Crazybee F3 PRO Flight controller 1-2s Lipo compatible 2S whoop more powerful and more flight time New 0802 Powerful and High efficiency Brushless motor and Smooth ESC. Betaflight support , multi flight mode ACROAIRANGLE Betaflight OSD support ,easy to get RSSI, Voltage ,current from your gogglesDSMX version no RSSI output. Smartaudio ready , change VTX bands, channels via OSD Adjust the settings and the PID of the flight controller via OSD Full telemetry function ready Head lights ready Camera angle adjustable Real Bind and Fly version Buzzer Ready.

The ES24TX Pro Micro ExpressLRS TX module is a upgrade version of ES24TX module.. Max output up to 1000mw, reserved Cooling Fan and RGB LED module. This Micro TX module support most of the OpenTX radio transmitter that with Micro JR bay. And this time the ES24TX Pro module comes completely assembled before out of factory..

Length 10cm. Quantity 5PCS. Suit for Diamond F4, CrazybeeF4 V3.1, CrazyF411 flight controller and Speki receiver.