Top 10 Best Phone Grip Bulk

What you receive 30 pieces blank phone holders with double-sided sticker Adequate quantity to satisfy your daily use and replacement You can paste your photos, epoxy finished products and beautiful flowers Enjoy your DIY time and you can share them with family and friends Note this package does not contain sublimation blanks. Size and material each blank phone holder has a diameter of 4 cm 1.58 inches, made of durable ABS plastic and strong adhesive which is a suitable size for decorating the phone and easy to be held in hand The holder ensure long service life and strong viscosity can help you grip the electronic equipment and DIY decorate firmly and prevent it from falling due to sliding. Easy use the foldable finger stand convenient and practical to use as cable winder, finger grip, table kickstand, car mount holder and so on It can be folded in 180 degrees to change angle Easily adjust your favorite viewing angles to play phones or watch videos. Enjoy DIY the blank phone holder is nice for DIY customization according to your own ideas to design and enjoy your own cell phone grip. Widely use the kickstand hand grip is suitable for most electronic equipment, but not compatible with non-flat surface.

Sufficient amount there are 12 pieces of sublimation phone holders in one package, simple but stylish, easily complements with any phones styles, sufficient quantity to meet your requirements. Suitable size to hold the phone grip holder measures approx. 3.8 cm 1.5 inches in diameter, which decorates your phone in a suitable size for easy grip, they offer a secure grip so you can text with one hand, snap better photos, and watch videos. Customize your phone holder the adhesive finger holder can withstand heat up to 400 degrees for 60 seconds and can be sublimated on with wanted images, you can use a heat press to press image on it to design your own mobile phone stand, making your phone novel and eye-catching. Convenient to use you should firstly paste adhesive sticker on the back of the bracket, then peel off the protective paper on the sticker, paste the sublimation piece, and tear off the protective film on the other end of bracket, finally stick it on your smartphone, finished. Applicable occasions you can use these adhesive phone stand brackets on various occasions, such as in work, travel, restaurants, coffee shop, office, school, home and so on, which helps you hold your device safely at any time, our phone stand brackets fit for various devices, such as mobile phones, tablets, etc..

15 Different colors there are 15 pieces of silicone phone holders in 15 different colors, the colors include pink, black, rose gold, transparent, orange, etc., sufficient colors can support replacement according to your personal mood. Size detail each phone grip holder measures 3.9 x 0.8 x 0.2 inch, which can be widely applied for many electronic products such as mobile phones and tablets It is also very convenient for you the carry when you go outside. Simple operation the push-pull design of the phone grip holder makes it easier and more convenient to use Tearing off the adhesive, sticking the holder on your phone case, finally pushing the grip stand upward, then the whole operation is finished. Quality material made of quality silicone, these telescopic finger strap brackets are durable, not easy to break, can last for a long time The strong adhesive protects your phone from falling, bringing you great using experience. Wide application the phone holder can support phones, tablets and other electronic devices to stand, releasing your hands when you want to watch TV, movies and sports matches on your devices, providing a lot of convenience to you.

Sufficient amount there are 25 pieces of sublimation phone holders in white, simple but stylish, easily complements with any phones styles, sufficient quantity to meet your different requirements. Suitable size the phone grip holder measures approx. 3.8 cm 1.5 inches in diameter, which decorates your phone in a suitable size for easy grip, they offer a secure grip so you can text with one hand, or snap better photos and watch videos. DIY design the adhesive finger holder can withstand heat up to 400 degrees for 60 seconds, and can be sublimated on with wanted images, you can use a heat press to press image on it to design your own mobile phone stand, making your phone novel and eye-catching. Convenient to use you should firstly paste adhesive sticker on the back of the bracket, then peel off the protective paper on the sticker, paste the sublimation piece, and tear off the protective film on the other end of bracket, finally paste it on your smartphone. Applicable occasions you can use these adhesive phone stand brackets on various occasions, such as in work, travel, restaurants, coffee shop, office, school, home and so on, which helps you hold your device safely at any time, the phone stand brackets fit for various devices, such as mobile phones, tablets, etc..

Package includes you will receive 6 pieces elastic finger holders for phones in different colors, including 1 piece rose gold, 1 piece gold, 2 pieces black and 2 pieces silver, enough quantity for your daily use and replacement, or you can share with your friends. Elastic design the phone finger holder can help you hold your mobile device comfortably and steady, so you can easily touch the screen and relax your fingers, and it enables easier one-handed texting, photos, selfies and so on. Strong viscidity there is a adhesive on the back of the phone holder, which has strong adhesiveness can be applied for a long time without falling off easily, so it can firmly support your phone And there will be no residues when you take it off. Widely applicable these finger grip straps are suitable for 4 - 8 inch smartphones, tablets and other similar digital devices, which are easy and quick to install, convenient for you to hold your phone securely and stably. Portable size each cell phone stand measures approx. 2.87 inch in length, 0.86 inch in width, thin and lightweight, so it can slide easily into your pocket or carry it out with your phone, which will not take up too much space.

PopGrip with swappable top switch out your PopTop for another design or remove it completely for wireless charging capabilities. Offers a secure grip so you can text with one hand, snap better photos, and watch videos hands-free. Use with a PopSockets PopMount 2 and go hands free. PopGrips are compatible with PopWallet, Otter Pop cases, PopPower Home Wireless Charger, and PopMount 2. Sticks best to smooth hard plastic cases. Sticks to iPhone 11 will not stick to iPhone 11 Pro or iPhone 11Pro Max without a suitable case..

LoveHandle Grip Helps You To Stop Dropping Your Smartphone and Tablet Enables easier one-handed texting, photos, selfies, and holding your smartphone or tablet. Slim pocket-friendly design Soft comfortable elastic grip Safe no-residue removable 3M adhesive, See directions below on how to setup the LoveHandle grip. 100 Satisfaction Guarantee Size LWH 2.63 x 0.88 x 0.13 inches Please Note On-screen images of finishes and colors may vary from actual product due to variations in monitor and image capture settings. Compatible with most Smartphones and Tablets, For Smartphones or Cases that are waterproof or have anti-fingerprint properties, we recommend applying the LoveHandle Adapter Adhesive before placing the LoveHandle grip on your device. LoveHandle, SlingGrip, DMD Products, and all other trademarks are the property of their respective owners. Please Note On-screen images of finishes and colors may vary from actual product due to variations in monitor and image capture settings.

Package includes there are 20 pieces sublimation phone holders set, each set includes 1 phone grip holder base, 1 double-sided film and 1 aluminum sheet, sufficient for personal use or designing a finished product for your friends. DIY phone holder this product is a blank hot sublimation mobile phone bracket All the blank accessories you receive are unprocessed, which allow you to use a hot press to DIY some patterns on it, so that you can get personalized mobile phone bracket. Easy to finish you just need to stick the double-sided film on the aluminum sheet that has been sublimated, then stick the aluminum sheet on the top of the phone holder, and finally tear off the adhesive at the bottom of the phone holder and stick on the phone, the whole operation is quite simple and easy. Quality material made of quality plastic material, these sublimation phone holders are sturdy, lightweight, and can last for a long time, the strong adhesiveness enables it to attach to your mobile phone firmly, which can bring a pleasant using experience to you. Size detail each phone grip blank comes in about 4.3 cm 1.7 inch in diameter, and you can adjust its height according to your own usage and personal need.

Free Rotation 360 degree rotation and 180 degree fold help you adjust your phone to different viewing angles to reading, watch videos. When received the cell phone finger ring, you will see the white one. Tear up the white sticky film in the back of finger ring, then they will be transparent .. Unique Design This phone finger holder is made to be transparent, allowing you to keep the unique design of your phone case but also giving you the features of having a phone ring holder.. Durable Material Durable material and strong adhesive sticky to make the finger ring grip can be glued to the back of your tabletsphones or their cases firmly make sure easy installation. Please do NOT pull the finger ring stand after you stick it on your phone, because the adhesive is not sticky enough within the next 24 hours.. Strong Firmly Grip The cell phone ring grip holds devices firmly, prevents your phone from dropping reduces the risk of theft, while you are operating phone or taking photos. The cell phone ring holder can also be used as kickstand.. Universal Compatibility Will fit any flat and non-textured surfaces.Clear cell phone kickstand ring be used on most smart phone and tablets..

Compatible Phone Models and Phone CasesThis magnetic phone grip is only compatible with iPhone 12, 13 series, including iPhone 13 iPhone 13 Pro iPhone 13 Pro Max iPhone 13 mini, iPhone 12 iPhone 12 Pro iPhone 12 Pro Max iPhone 12 mini. Note Please use without a case or with an iPhone-compatible magnetic phone case, or stick a magnetic metal ring to ordinary case for magnetic capability. Support Wireless ChargingThis phone ring holder highly supports the need for wireless charging. You can easily detach it from your phone for wireless charging, then attach it again after charging is done. The magnetic attraction stays strong and stable all the time. No Residue Left Strong Magnetic ForceMagnetic attraction leaves no trace at all. Say goodbye to stick residue. The magnetic force is strong enough to hold up to 28 oz 800 g, which is equivalent to the weight of 4 iPhone 12. No worries of accidentally drop your phone while use this phone finger holder. 360 Rotation and 150 FlipThis ring for phone case features 360 Rotation so you can easily switch angles between vertical stand and horizontal stand. The phone holder for hand is also capable of 150 Flip so you are able to adjust it to the most comfortable viewing angle as you need. High Quality and Ultra SlimThis phone hand holder features high quality finish and smooth polished metallic material, adding style to your phone. It is slim and flat, easy to carry. Never gets caught pulling it in and out of your pocket..