Top 10 Best Poe Splitter 5v

5.5x2.1mm DC Plug Active PoE Splitter48V to 5V 2.4A Max. 12watt. 10100Mbps EthernetCompliant with IEEE802.3afWith 2.5KV isolation. This POE Splitter is suitable for household IP camera with DC 5V power as the kind in the photo of the instruction,it does not suit equipments with DC 12V power. Some managed intelligent Gigabit PoE switches need to set the LAN port of this connected splitter to Manual 100Mbs mode in the management Settings of switches, otherwise the power supply may work normally but the network connection will not work, such as the following switch, HP 3500-48G-PoE yl Switch J8693A.

What is it - A UCTRONICS PoE splitter to split the PoE signal into 5V USB-C power supply and gigabit Ethernet in RJ45 so that non-PoE devices can be powered over Ethernet.. What is PoE Deliver power and data with a single Ethernet cable for fewer wall plugs and messed cables. Extend powerline to where no AC outlets are nearby, up to 300 feet away from the power source. Why PoE to USB-C A cost-effective way to add plug-and-play PoE support to 5V USB-C powered devices and make full use of PoE switches, or for a Raspberry Pi 4 setup where a PoE HAT is not applicable. What else needed - You need an IEEE 802.3af compliant PoE switch or injector to serve as the PSE Power Source Equipment and an Ethernet cable with PoE signal to feed the splitter.. Note 1. This splitter does not support PD or QC fast charging protocols. 2. This splitter provides a maximum output of 2.4A with its 802.3af compliance. Check B07V35DH5F for power-hungry applications. 3. Just put the split Ethernet aside if you dont need the data. 4. The Split Ethernet cable does not carry power anymore..

48V to 5V 2.4A Max. 12watt. Compliant with IEEE802.3af. With 2.5KV isolation.

OUTPUT 5V DC power out 5V 2.4A 12watts Max., plug micro USB, 10100Mbps ethernet data. INPUT IEEE 802.3af DC44-56V from poe switch or poe injector, deliver power up to about 100m 328 feet. PLUG and PLAY Require no configuration, a simple solution to expand your network to where you wish to place network devices but has no power outlet. APPLICATION works with non-PoE network devices that have a 5V micro USB input and a ethernet input, such as IP camera, Tablets, Dropcam or Raspberry Pi and more. please note this spitter is only compatible with 10100Mbps non-PoE devices, it DOES NOT support gigabit non-PoE devices like Raspberry Pi 3B. WARRANTY 2 years and unlimited technical support, Package content 4x 5V PoE splitter.

12 watt micro USB Power over Ethernet PoE up to Remote 328-492ft 100-150m via Ethernet cable, 802.3af PoE switch or 48v injector is needed. Power Output Port 5V 2.4A Micro USB Power Plug. Compatible with 44-57V DC voltage, overvoltage protection. Support IEEE 820.3af PoE Switch, 48V Unsolicited Power Over Ethernet PoE Switch or Ethernet PoE Adapter, 48v injector. For gigabit PoE switches users, gigabit splitter U515902 is recommended. Suitable for Android Tablets, Dropcam, Raspberry Pi Micro USB. 2-Pack B07QPRVM51.

The POE splitter must be connected to the POE switch, POE midspan or 48V52V POE injector for proper operation.

OUTPUT 5V DC power out 5V 2.4A 12watts Max., Plug 3.5mm x 1.35mm, 5.5mm x 2.1mm , 101001000Mbps ethernet data. INPUT IEEE 802.3af DC44-56V from poe switch or poe injector. PLUG and PLAY Require no configuration, a simple solution to expand your network to where you wish to place network devices but has no power outlet. APPLICATION works with non-PoE network devices that require a 5V dc input and a ethernet input, such as IP camera and more. WARRANTY 2 years and unlimited technical support, Package content 2x 5V PoE splitter.

Split POE siganl into Ethernet date 1000Mbps max and USB-C or 5.5x2.1mm barrel port DC power 5V4A max, Fully complies with IEEE 802.3afat POE Switch or Injector Required but not included, Output 20W max 5V4A at 802.3at and 12.5W max 5V2.5A at 802.3af.. PoE HAT Alternative - Alternative way to achieve POE function for Raspberry Pi 4 and NVIDIA Jetson Nano, No need to dismount raspberry pi case or add-on screen anymore by using AuviPal POE Splitter.. It utilizes the optimal PoE module solution with isolation transformer Standard PD Powered Devices chip. Run your Raspberry Pi and NVIDIA Jetson Nano more stable and safer.. Plug and play - Simply connect the ethernet and power cables, then you are ready to go. Set it up in seconds without any extra effort or configuration.. Suitable for NVIDIA Jetson Nano and any USB-C Devices Raspberry Pi 4, Camera, Phone, Tablet and more..

What is it - A 5v UCTRONICS PoE splitter to split the PoE signal into micro USB power supply and Ethernet in RJ45, so that non-PoE devices can be powered over Ethernet. Reportedly used on micro USB devices like Raspberry Pi, Amazon Ethernet Adapter for Fire TV, Amazon Cloud Cam, Echo Dot 2nd Gen, Wyze Cam v2, Arlo 2 Pro, ASUS Tinker Board, Nano Pi, Chromecast, and so on. What is PoE - PoE enables you to deliver power and data with a single Ethernet cable, and thus fewer wall plugs are needed and fewer cables are messed. It also helps you extend powerline to where there are no AC outlets nearby but your Ethernet cable can reach, up to 300 feet away from the power source. Whats special about it - PoE to Micro USB. That means it adds plug-and-play PoE support to Raspberry Pi models even they are not 3 B and cannot accommodate a Raspberry Pi PoE HAT. It makes full use of PoE switches because the other end of the PoE port could be any micro USB devices instead of a 48V PoE network device. What else is needed - You need an IEEE 802.3af compliant PoE switch or injector to serve as the PSE Power Source Equipment, an Ethernet cable with the proper length you need, and devices powered via micro USB. These are not included in our package. Note - 1 Just put the split Ethernet aside if you dont need the data. 2 For one pack, check B01MDLUSE7 For gigabit PoE switch or a Raspberry Pi 3 B, check Gigabit PoE splitter B07CNKX14C For 12V barrel port, check B01MPWW2UV. 3 The Split Ethernet cable does not carry power, but you can add a USB Ethernet adapter to it if your device takes network from USB.

802.3af PoE Splitter Converter for 5 volt non-PoE devices - Extend power up to 328 feet from power source. Compatible with Cameras, Tablets, Raspberry Pi, Smart home devices and more - 1.35mm x 3.5mm DC barrel fits most devices. Converts and splits 44-57v PoE into 5 volts, 10 watts with divided 101001000 gigabit data capability. Requires an IEEE 802.3af PoE switch or injector sold separately - See compatible options below. Backed by 1 year warranty - For expert technical support from Austin, TX please call 512 479 0317.