Click here to learn more about these products.
Rheem Ruud Weather King, RGP Mid Efficiency, Conquest 800 Furnace Draft Inducer Blower FB-RFB241
This Aftermarket Replacement Furnace Inducer Motor is a Direct Replacement for RheemRuudWeather King Units.. No Modifications Required. Not an OEM product.
Ruud 62-24164-01 Ignitor Spark
This Is A Genuine Oem Replacement Part. Country Of Origin United States. From The Brand Name Ruud. Model Number 62-24164-01.
Duralight Furnace Ignitor Direct Replacement For Rheem Ruud Weatherking OEM Part 62-22868-93
Duralight Two Year Replacement Warranty. Made In USA. Exact Fit with No Adapters or Wiring Changes Required. Direct Replacement Part For Most Rheem, Ruud, Weatherking Furnaces With Hot Surface Ignitors - Will Not Fit Drum Heat Exchanger Type Furnaces. Replaces Part Numbers 62-22441-01, 62-22548-01, 62-22868-01, 62-22868-02, 62-22868-82, 62-22868-92, 62-22868-93S, 62-22869-01, 62-23460-01, and 8553-5514.
OEM Upgraded Rheem Ruud Weather King Corsaire Furnace Control Circuit Board 62-24084-02
BRAND NEW OEM Upgraded Control Board. Upgrade Kit comes with wiring instructions. LED Diagnostic for Easy Trouble Shooting.
Furnace Vent Air Pressure Switch - Fits Ruud Gas Part # 42-24335-02
This is a Brand New Gas Furnace Air Switch. Top Quality Furnace Air Switch. Made in the U.S.A.
OneTrip Parts Furnace Pressure Switch High Temp Tubing 3/16 I.D. X 18" Replaces Rheem Ruud Weatherking 79-21491-83
OneTrip Parts Two Year Replacement Policy. 392 Degree F Temperature Rating. Replaces 35 OEM Part Numbers. 316 Inside Diameter - 18 Long. Direct Replacement for Many Rheem, Ruud, and Weatherking Furnaces.
OEM Upgraded Replacement for Ruud Furnace Flame Sensor 62-23543-03 by Ruud
This is a Brand New Furnace Flame Sensor. When the flame sensor goes bad, the furnace will light for several seconds and then turn back off on the flame sensor safety.
Furnace Vent Air Pressure Switch - Replacement for Rheem ClimaTek Gas Part # 42-24335-02
This is a Brand New Gas Furnace Air Switch. Top Quality Furnace Air Switch. Made in the U.S.A.
62-23543-01 flame Sensor Rod furnace ignitor for gas furnace fit for Rheem（2 pack）
Replacement model62-23543-01,62-23543-02,62-23543-03,62-23543-04. Applicable circumstancesDetect when the burner flame ignites and send a signal to the control panel to stop the ignition. Length mounting flange to sensor tip 2-12, length-sensor offset 1-916. Angle sensor offset 90 degrees. Termination 14 male thread quick connect.. Excellent quality made of high quality and hard wearing metals and ceramics, well tested and durable.. Easy to install, cost-effective You can easily replace damaged sensors by following our installation process. Help you save equipment costsBefore installing this component, disconnect the power and turn off the air source. Wear work gloves to protect your hands.. Satisfactory service For any reason you are not completely satisfied with the product, you can ask for a replacement or a full refund. If you are unsure whether this flame sensor stick is suitable for your device, please feel free to contact us or ask questions through Amazon..
117104-01 - Rheem Furnace Draft Inducer/Exhaust Vent Venter Motor - OEM Replacement
This is a Brand New Furnace Replacement Inducer Motor Kit. Univeral Design and Easy Installation Make this a Top Qualty Replacement Part.
Best Choice
Best Value
