Top 10 Best Snugtop

Snugtop Pop out lock.

Snugtop Hinge outer plate set each.

Snugtop Camper Shell Strike Loop Driver side. New Heavy Duty loop replaces all old styles..

Snugtop Camper Shell Strike Loop Passenger side. New Heavy duty loop replaces all old styles.

CHECK YOUR LENGTHS AND PRESSURE BEFORE ORDERING. THESE ARE NOT COMPATIBLE WITH ALL SNUGLID TONNEAU COVERS THE MEASUREMENTS ARE FROM CENTER OF BALL MOUNT TO CENTER OF BALL MOUNT, NOT FROM END TO END OF STRUT SEE PICTURE. Truck Upfitters Pair 2 total of 80 pound each gas struts. 26.5 extended length and 15.4 compressed length. Most commonly used and compatible with for SnuglidSnugtop brand SL F2 models and compatible with Snuglid style Tonneau covers with 2 single lift assist arms. Fits other similar brand of fiberglass tonneau covers truck lids, but measurement is required to ensure fit.. These are not compatible with all Snuglid fiberglass tonneau models they do NOT fit ANY SL2 or RL models. Measure your strut from center of socket to center of socket when fully opened and fully closed to get accurate measurement. Also check for 80 pounds of pressure, or 355N - 356N Newtons of pressure and part number 713119 on the strut. We also offer 29.5 long props for longer beds, in 80, 90 and 100 lb pressures.. Comes with four threaded 13mm ball mounts and nuts for alternate 'other than tonneau cover' applications, such as in RV doors and awnings, boat hatch spring lifts, storage bed lifts, etc. These gas shock lift supports CANNOT be compressed by hand. These gas props MUST be installed in the EXTENDED OPEN position. It is nearly impossible to install them in the CLOSED position. Please refer to the install video for guidance on how to install.. Compatible with some but not all Snuglid SL and F2 Shortbed and Extrashort bed 5.5-6.5' Truck Tonneau Covers with single lift arms see picture. Check your original struts for part numbers Compatible with Snugtop 713119 or compatible with Stabilus 202677..

Snugtop All glass door hinge, each.

Snugtop Strike loop new style SL.

Snugtop Parts Clamp Kit for Snugtop Campers.

CHECK LENGTHS AND PRESSURE BEFORE ORDERING. THESE DO NOT FIT ALL CANOPY and COVERS THE MEASUREMENTS ARE FROM CENTER OF BALL MOUNT TO CENTER OF BALL MOUNT, NOT FROM END TO END OF STRUT SEE PICTURE Use a measuring tape to measure the door gas strut that you are replacing. Measure from the CENTER of the gas prop head little plastic end, to the other side. DO NOT measure from the end of the gas prop, your measurement will be too long. Note that most applications allow for 1-5 size variation.. Truck Upfitters Pair of 38 pound each gas struts. 15.7 extended length and 9.4 compressed length. This size of door shock absorber is for tall medium weight rear or side camper shell doors. Each canopy shock has 38 lbs of pressure, for a total of 76 lbs of pressure. Please note that this does not mean that it can lift something that is 76 lbs. the typical hinged-style door weight for this prop is approximately 50-70 lbs, including the weight of the camper shell locks and keys.. These gas lift cylinders do not fit all truck capcamper shell brandsmodels. Measure your strut from center of socket to center of socket when fully opened fully closed to get accurate measurement. See pictures to determine how to measure. Do NOT measure from end to end. Measurement must be from the center of plastic ball mount on each end of the gas spring lift. Measurement is important to ensure they open properly and get a good camper shell seal against the camper shell gasket when closed.. Comes with four 10mm ball mounts for alternate 'other than truck camper shell' applications, such as in camper canopy windoors, RV doors and awnings, boat hatch spring lifts, gas struts for cabinets, storage bed lifts, toolbox struts, etc. These gas shock lift supports CANNOT be compressed by hand. These gas props MUST be installed in the EXTENDED OPEN position. It is nearly impossible to install them in the CLOSED position. Please refer to the install video for guidance on how to install.. Equivalent to Suspa c16-09209 or Stabilus 01824. These camper shell shocks are compatible with many truck canopy types, including LEER truck cap parts, ARE truck topper parts, Glasstite parts, Century parts, Snugtop replacement parts Astro tops, ATC campers, and many other fiberglass brands that utilize gas shocks gas springs gas lift cylinders. Compatible with many gas lift brands, including stabilus, lift o mat, and Suspa. These are OEM quality and perfect fit for your topper.