Top 10 Best Vacuum Switch For Power Tools

Use high-quality materials UL-certified US standard 3-pin AC power socket. UL-certified US standard 14AWG power cord. And the switch's shell is made of PA-765 flame retardant material. Make you safer and more reliable at work.. Automatic turn on the vacuum when you start your tool , and delays 10 seconds to turn off the vacuum to clean the pipe when you complete your work. Saving time and electricity, reducing airboin toxin and noise that may lead the health problem. This can protect your health.. Package Included 1x vacuum switch with 15'' power cord 1x Installation instruction. Suitable for most medium duty workloads. Perfectly suited for medium-sized work loads such as most Miter Saws, Table Saws, Power Sanders and Routers, and extend the life of your vacuum.. The total current of all electrical appliances used with this device must not exceed 15A when operating, and the electrical cutting tool can only be used at the TOOL socket and cannot be used by inserting it in the VAC socket..

NEW GENERATION Add a manual switch to support three vacuum run modes Auto, Off and On. You can not only turn the vacuum onoff automatically with the power tools, but also manually turn the vacuum onoff all time according to your actual condition.. HIGH-QUALITY MATERIALS Adopt 19.7 inch UL-certified US standard 14AWG power cord which allow passage with a large current more than 30A. Durable PCABS V0 grade flame retardant material case, reduce heat during use and extend service life.. TURN ON DELAY. Load Sensing Technology. If the load connected to the 'TOOL' port exceeds 30W, the vacuum connected to the 'VAC' port will automatically delay 1s to start, which helps prevent circuit overloaded by large current if tool and vacuum power-on at the same time.. SHUT OFF DELAY Automatically delay vacuum turn-off by 7s to continue clearing the remaining airborne debris after the load connected to the 'TOOL' port has stopped. Saving time and electricity, reducing airborne toxin and work area noise that can lead many health problems.. COMPATIBILITY Support a wide range of cutting tools from handheld devices to large shop saws such as table saw, miter saw, track saw, chop saw, sander, router table, planers, shopvac, remote control outlet, automated vacuum switch, dust collection systems for woodworking and etc. Power rating should not exceed 120 VAC, 15 Amp, 60 Hz, 1875w..

NEW GENERATION Addition of two tool outlets, no need extra extension socket, avoid messy cords and save time Three vacuum run modes can be switch freely Auto, Off and On The values are clearly displayed with LED indicators, each key for corresponding option, easier to check and set.. CONFIGURABLE ACTUATION THRESHOLD 30W60W, you can select flexibly appropriate actuation threshold according to your actual condition. Prevent vacuum from running too long or being unable to shut off after tool has stopped.. CONFIGURABLE SHUTOFF DELAY TIME Automatically delays vacuum turn-off by an optional time 3s7s10s to continue clearing the remaining airborne debris after the tool has stopped, which reducing work area noise and improve work efficiency.. TURN ON DELAY SAFETY Automatic delays 1s to turn on the vacuum when you start your tool, which avoids circuit overload or tripping. Adopting UL-certified American Standard 14AWG power cord which allowable passage with a large current more than 30A. Thick copper core, covered with PCABS V0 grade flame retardant material, less heat during use and extend service life.. COMPATIBILITY Supports a wide range of cutting tools from rotary handheld devices to large shop saws such as Miter Saws, Table Saws, Power Sanders, Routers, Joiners, Planers etc. Max motor rating should not exceed 120V15A 5060Hz, 1875W..

No Overload Any More - If the tool motor connected to the '' port exceeds 27.5W, the vacuum connected to the '' port will automatically delay 0.5s to turn on, which helps prevent circuit overloaded by large current if tool and vacuum power-on at the same time. NOTE The current sum of the tools used on III should not exceed 15 amps. Pls check if it fits before buying.. 0.5s Auto Delay Control for the Vacuum On - The shorter the delay, the faster your vacuum will work, the cleaner your home will be. Automatic delays 0.5s to turn on the vacuum when you start your tool, which is more fast than other switches in the market. Why not make your home a little cleaner. 5s Auto Delay Control for Vacuum OFF - When you turn off your power tools, delays 5s to turn off the vacuum. After careful calculation and investigation, we find that 5S is enough to completely clean up your Inlet tube when you complete your work. So just saving your time,energy and electricity.. Premium Material Makes Extreme Durable and Safe - UL-certified 14AWG power cord which is US standard. Control box covered with full ABS V0 grade flame retardant material, more safe and reliable.. Wide Compatibility - Our automatic vacuum switch has a starting threshold of approximately 0.25 amps 27.5watts at 110V, perfectly suited for medium-sized work loads such as most Miter Saws, Table Saws, Power Sanders and Routers, and extend the life of your vacuum.. NOTE III current should not exceed 15 amps, otherwise it is easy to overload.Please read the manual carefully before use to know the power range of the switch ..

NEW GENERATION Addition of two tool outlets, no need extra extension socket, avoid messy cords and save time Three vacuum run modes can be switch freely Auto, Off and On The values are clearly displayed with LED indicators, each key for corresponding option, easier to check and set.. CONFIGURABLE ACTUATION THRESHOLD 30W60W, you can select flexibly appropriate actuation threshold according to your actual condition. Prevent vacuum from running too long or being unable to shut off after tool has stopped.. CONFIGURABLE SHUTOFF DELAY TIME Automatically delays vacuum turn-off by an optional time 3s7s10s to continue clearing the remaining airborne debris after the tool has stopped, which reducing work area noise and improve work efficiency.. TURN ON DELAY SAFETY Automatic delays 1s to turn on the vacuum when you start your tool, which avoids circuit overload or tripping. Adopting UL-certified American Standard 14AWG power cord which allowable passage with a large current more than 30A. Thick copper core, covered with PCABS V0 grade flame retardant material, less heat during use and extend service life.. COMPATIBILITY Supports a wide range of cutting tools from rotary handheld devices to large shop saws such as Miter Saws, Table Saws, Power Sanders, Routers, Joiners, Planers etc. Max motor rating should not exceed 120V15A 5060Hz, 1875W..

Unique Current Sensing Technology. If the tool motor connected to the 'A' port exceeds 30W, the vacuum connected to the 'B' port will automatically delay 1s to turn on, which helps prevent circuit overloaded by large current if tool and vacuum power-on at the same time. Make the Work More Effective. Automatic delays 1s to turn on the vacuum when you start your tool, and delays 7s to turn off the vacuum to clean the inlet tube when you complete your work. Saving time and electricity, reducing airborne toxin and work area noise that can lead many health problems. Suitable for Most Medium Duty Workloads. Etoolcity automatic vacuum switch has a starting threshold of approximately 0.25 amps30watts at 120V and 60watts at 220V, perfectly suited for medium-sized work loads such as most Miter Saws, Table Saws, Power Sanders and Routers, and extend the life of your vacuum. More Safety. Adopting high-cost, UL-certified American Standard 14AWG power cord which allowable passage with a large current that more than 30A, the Etoolcity Automatic Vacuum Switch can work stably within 3600W. The switch's shell has PCABS V0 grade flame retardant material, it is more reliable and safe to protect work. Two Installation Methods. You can use screws to fix the power module part, or use strong nano-markless hook sticker to attach directly to the wall. Both ways are very strong.

NEW GENERATION Addition of two tool outlets, no need extra extension socket, avoid messy cords and save time Three vacuum run modes can be switch freely Auto, Off and On The values are clearly displayed with LED indicators, each key for corresponding option, easier to check and set.. CONFIGURABLE ACTUATION THRESHOLD 30W60W, you can select flexibly appropriate actuation threshold according to your actual condition. Prevent vacuum from running too long or being unable to shut off after tool has stopped.. CONFIGURABLE SHUTOFF DELAY TIME Automatically delays vacuum turn-off by an optional time 3s7s10s to continue clearing the remaining airborne debris after the tool has stopped, which reducing work area noise and improve work efficiency.. TURN ON DELAY SAFETY Automatic delays 1s to turn on the vacuum when you start your tool, which avoids circuit overload or tripping. Adopting UL-certified American Standard 14AWG power cord which allowable passage with a large current more than 30A. Thick copper core, covered with PCABS V0 grade flame retardant material, less heat during use and extend service life.. COMPATIBILITY Supports a wide range of cutting tools from rotary handheld devices to large shop saws such as Miter Saws, Table Saws, Power Sanders, Routers, Joiners, Planers etc. Max motor rating should not exceed 120V15A 5060Hz, 1875W..

2640 TOTAL WATTS two input power cords permit operation from two separately protected circuits.. TURN ON DELAY avoids the two power surges occurring at the same time.. TURN OFF DELAY ensures that your work area continues to be cleared of remaining airborne debris.. Modes of operation Auto, Off and On. Dust Collector Shop Vacuum up to 1HP or 5 Peak HP.. NO VENTING HOLES the iVac's internal components are designed to generate very little heat..

IMPROVE WORK EFFICIENCY Automatically delays 1s to turn on the vacuum when you start your tool, which avoids circuit overload or tripping. Delays 7s to turn off the vacuum to continue clearing the hose of remaining debris after the tool has stopped, which reduces noise. Without running back and forth to hit the vacuum power button, this makes your work more effective. PROTECT YOUR HEALTH Fully automatic on off control means less dust Using Etoolcity automated vacuum switch efficiently minimizes hazardous airborne dust to protect your lung, and helps to comply with OSHA requirements for dust control. COMPATIBILITY Etoolcity dust collector switch supports a wide range of cutting tools from rotary handheld devices to large shop saws such as Miter Saws, Table Saws, Power Sanders, Routers, Joiners, Planers etc. Max motor rating should not exceed 120V15A 5060Hz, 1875W. SUPERIOR MATERIAL MAKES DURABLE Adopting UL-certified American Standard 14AWG power cord which allowable passage with a large current more than 30A. Covered with PCABS V0 grade flame retardant material, Thick copper core, thicker wire, less heat during use and extend service life. A safety must-have in the workshop. EASY TO USE Very easy to use Etoolcity vacuum switch in only 3 easy steps, just plug it in and you are ready to go. The text VACUUM OUTLET and TOOL OUTLET etc. are clearly printed on the surface to make sure you plug the tool and vacuum into the correct socket.

NEW GENERATION New functions to detect various power parameters in real time, such as power, volts, amps, kilowatt-hours, accumulated time, making it an intelligent steward for you. By accurate monitoring, it can help you reduce your electricity bill, a stable voltage environment also avoids damage to the power tool, and let you notice the working hours, remind you to combine exertion and rest. CONFIGURABLE ACTUATION THRESHOLD 30W60W, allowing you to flexibly select different vacuum actuation threshold according to your actual condition. Prevent vacuum from running too long or being unable to shut off after tool has stopped.. CONFIGURABLE STARTUP SHUTOFF DELAY TIME Automatically delays to turn on the vacuum by an optional time 0.1-3s when you start your tool, which avoids circuit overload or tripping. Auto delays vacuum turn off by an optional time 1-30s to continue clearing the remaining airborne debris after the tool has stopped, which protects your respiratory health, reduces work area noise, improves work efficiency.. EASY TO SEE LCD screen more intuitively displays various power parameters in real time including power, volts, amps etc. Each key for corresponding option, can be flexibly set according to personal needs, easier to operate.. COMPATIBILITY Supports a wide range of cutting tools from rotary handheld devices to large shop saws such as Miter Saws, Table Saws, Power Sanders, Routers, Joiners, Planers etc. Max motor rating should not exceed 120V15A 5060Hz, 1875W..