Top 10 Best Zero Clearance Table Saw Insert

4 ZERO CLEARANCE INSERTS FOR Dewalt 744, 745, 746, 7480, 7491, 7491RS and 7490 Type 1. DO NOT PURCHASE FOR DEWALT 7485 MODELS.WE SELL DIFFERENT INSERTS FOR THE DWE 7485 AND DCS7485 MODELS.. LEVELING SCREWS DEPENDING ON YOUR SAW TYPE, THE LEVELING SCREWS MAY NEED TO BE SET FROM THE UNDERSIDE OF THE INSERT. SEE PRODUCT DESCRIPTION FOR ADDITIONAL GUIDANCE.. NOT INTENDED TO USE WITH THE RIVING KNIFE IN PLACE. IF YOU WANT TO USE IT, YOU WILL NEED TO MAKE YOUR OWN CUTOUTS TO ACCOMMODATE FOR IT..

MEASURE YOUR FACTORY INSERT AND COMPARE SIZE BEFORE YOU ORDER. Zero Clearance inserts are table saw specific. Since every table saw brand and manufacturer is different, we recommend that you measure the exact length, width and thickness of your table saw insert or opening and compare it to the size we list. Also be aware of the shape of your current insert of whether its round, square ends or if there are any indents or protruding notches. Insert colors may vary from images shown.. If you own a table saw, then you probably have had smaller pieces of wood get caught between the saw blade and the factory supplied throat plate opening. This can cause that piece of wood to jam up against the blade and go flying across the room or worse yet, right back at you. Zero clearances help minimize this situation from happening since there is no gap between the blade and the zero clearance opening. The opening is more like a custom slot cut to the exact width of your table saw blade.. Another great reason to use a zero clearance insert is to help reduce that pesky and irritating tear out you always tend to get on your cuts. Without a zero clearance, the wood has no support by the blade to prevent the wood from tearing out. This is especially true when cutting plywood. Zero clearance inserts help prevent tear out by essentially enveloping the blade on all sides which doesnt allow the wood to tear out since there is not gap between the blade and insert.. Zero Clearance inserts can be used in conjunction with most any table saw blade including thin kerf, standard kerf and carbide tipped blades. You can also use zero clearance inserts with dado blade sets. The reason you would use zero clearance inserts with dado blades is to reduce the amount of tear out the dado blade set produces. We recommend that you use separate zero clearance inserts for dado blades since the gap for dados will be much wider than standard width table saw blades.. This zero clearance insert is made from a high density phenolic material that was chosen for its ability to stand up to everyday workshop use. The insert features two Snug Fit sand-able side tabs that allow you to remove a little material at a time for a perfect fit if necessary. The insert also features a top and a side Snug Fit Screw for a tight fit to you saw with no movement.

The insert is blank so you can custom fit the blade slot by passing your blade through it.. Helps to prevent tear-out plus close the large factory gap.. Fits most 1988 and newer 10 Belt Drive Models, Ridgid TS-2412, TS-2424 TS-2400. 14 x 3 34 x 316.

Fits Delta Unisaw LEFT-TILT UNISAW, 10 Contractor,10 Tilt Arbor Saw, Hybrid Left-Tilt Contractor, Grizzly G1023, Jet CTAS-10, Powermatic 63, Sears Craftsman 22104, 22114, 22124, Bridgewood BW10TS, Steel City 35605, 35610, 35670, 35675, 35680, 35685. Measures 13-38 x 3-34 x 12 Please measure before ordering. Offers superior rigidity, flatness, durability, and low friction reduces chip-out and splintering. Elimantes dangerous gap around blade where thin off-cuts can get wedged. Includes leveling screws, side and end adjustment screws rear safety pin precut blade bottom pocket for fully retracted blades and bevel cuts.

The insert is blank so you can custom fit the blade slot by passing your blade through it.. Helps to prevent tear-out plus close the large factory gap.. 10 PRE 1988 Belt Dive. Alway be sure to measure your insert and compare it to the size listed below before ordering.. 14 38 x 3 34 x 316. Note Measure your factory insert to ensure proper fit..

MADE IN USA. HIGH DENSITY MDF SPRAYED WITH LACQUER. SET SCREWS NOT INCLUDED, IT FITS TIGHT. STURDIER THAN PLASTIC, CHEAPER THAN PHENOLIC. MINOR SANDING MIGHT BE REQUIRED FOR A PERFECT, TIGHT FIT, DEPENDING ON THE CASTING.

DWE7485 only zero clearance insert. Will not fit any other saw model. Check your saw type before ordering.

Insert Dimensions 12-12 x 3-916 x 716 - JT-164 JetPowermatic 64A Zero-Clearance Table Saw Insert. Made from high-density phenolic laminate with a bonded-melamine surface. Small Jet, Grizzly, Powermatic 64 insert will fitvarious models of table saws.. Includes leveling screws, side and end adjustment screwspre-cut blade bottom pocket. Please check your Length x Width x Thickness of your current insert before ordering.

4 ZERO CLEARANCE INSERTS FOR Skil 10 TS6307 TABLE SAW. INSERTS ARE PRECUT WITH A RIVING KNIFE SLOT.. NO LEVELING SCREWS NEEDED. INSERTS ARE DESIGNED TO FRICTION FIT.. MDF PAINTED SIDE RED.