Top 10 Best Zooz Z-wave

READ BEFORE YOU BUY The Z-Wave stick is for advanced users only, NOT for beginners. You must be comfortable with programming and have expert computer and Z-Wave knowledge to use this device.. S2 SECURE NEW 700 SERIES Z-WAVE PLUS Take advantage of the new 700 Series Z-Wave with more range and S2 authenticated security protocol. It means that you can fully benefit from your S2 sensors, switches, and plugs running on the latest Z-Wave chip.. WHAT YOU NEED This S2 700 Series Stick adds Z-Wave Plus capability to your DIY smart home set-up. You'll need a dedicated computer PC, laptop, or Raspberry Pi, sold separately and home automation software of your choice not included to complete the system.. ADVANCED Z-WAVE Works great with the most popular software like Home Assitant with JS, Indigo, and HomeSeer. Supports OTA firmware updates works with Aeotec OTA firmware tool and and all of the latest Z-Wave library commands.. SMART START Supports the new quick and extra secure Z-Wave pairing method. Just scan the QR codes from any SmartStart Z-Wave Plus accessories to your home automation interface and power them on. They'll join automatically. Make sure your smart home software supports this feature..

POWERFUL PLUG The only Z-Wave Plug that lets you safely control and monitor heavy-duty 110V appliances from your Z-Wave smart home system. Connect your refrigerator, humidifier or dehumidifier, AC unit, fan, sump pump, or a gas clothes dryer to Z-Wave. NEW 45 degree angled plug so you can fit 2 Smart Switches in a single receptacle. POWERFUL Z-WAVE With built-in Z-Wave Plus signal repeater and range test tool, the Power Switch will boost your whole Z-Wave network while keeping it protected with AES signal encryption.. POWERFUL CONTROL Monitor energy use of connected appliances in live mode or over time with W, kWh, A, and V reports your Z-Wave hub needs to support this feature. NOTE It is NOT a power outage monitor Quick status reports to the controller and onoff state recovery after power failure.. POWERFUL HARDWARE Made from high-quality components that will last, even when it's very cold or very hot 14 - 104F, indoor use only. ETL certified complies with North American electrical safety standards. Extra-thick flexible cord is perfect for installations with no immediate access to a receptacle.. COMPATIBILITY Use the Power Switch with any certified Z-Wave gateway for simple onoff control Wink, Z-Wave alarm panels. Advanced settings and energy monitoring available for open systems only, including Vera, SmartThings custom device handler required, contact seller first, HomeSeer, and Fibaro Home Center Lite..

MAIN BUTTON Connect a 120 V light fixture up to 150 W for LED's to control it via Z-Wave or use the main button for wireless control only with up to 7 button triggers available. Z-Wave hub required, sold separately. NOTE your smart speaker is NOT a Z-Wave hub.. 4 REMOTE BUTTONS Program each button to activate scenes or other devices in your network for one-touch control of your favorite smart lighting presets. Use the buttons to enter Away mode on your way out or to turn off all of the lights before you go to bed with a single click.. DIRECT 3-WAY SOLUTION No add-on switch needed Works with regular 3-way switches as long as NEUTRAL is present. Wire it just like the ZEN21ZEN71 models. Please follow the appropriate diagram in the manual and rewire both boxes exactly as shown. Works great as a single pole switch too. Z-WAVE HUB COMPATIBILITY Most basic Z-Wave systems aren't advanced enough to allow scene control programming. The ZEN32 Scene Controller is supported by SmartThings with a custom handler, instructions included with the product, Hubitat, Home Assistant, and HomeSeer. Please do NOT buy this device if your hub isn't listed here, it will not be recognized correctly by your system.. NEW 700 SERIES This product is built on the latest 700 series Z-Wave chip for better signal coverage than ever, faster communication, with S2 authenticated security and SmartStart for effortless pairing.. EASY INSTALLATION Clear diagrams and 7-day a week support included. No side tabs and just 1.1 deep to fit shallow and crowded switch boxes. NEUTRAL WIRE REQUIRED check before buying. The device is ETL certified and conforms with North American safety standards. Backed by a 5-year warranty..

REMOTE CONTROL Use the paddles like remote control buttons to trigger scenes and turn other smart home devices on or off. Z-Wave hub required, sold separately. NOTE your smart speaker is NOT a Z-Wave hub.. ANYWHERE SWITCH Install it in a regular switch box or stick it to any flat surface for convenient and wire-free control. This is a battery-powered device with a magnetic base that allows a flexible installation anywhere you always wanted another light switch no electrician needed.. Z-WAVE HUB COMPATIBILITY Most basic Z-Wave systems aren't advanced enough to allow scene control programming. The ZEN34 is supported by SmartThings with a custom handler, instructions included with the product, Hubitat, Home Assistant, and HomeSeer. Please do NOT buy this device if your hub isn't listed here, it will not be recognized correctly by your system.. NEW 700 SERIES This product is built on the latest 700 series Z-Wave chip for better signal coverage than ever, faster communication, with S2 authenticated security and SmartStart for effortless pairing..

VERSATILE APPLICATIONS Great to automate your garage door up to 3 doors with just 1 MultiRelay, commercial garage doors at your business, gas fireplace, sprinklers, doorbell, landscape lights, pool pump, whole house fan, and any 1-240 V device up to 20 A.. DIY INSTALLATION Power it with a standard USB C cable and a 5V power supply do NOT use USB chargers or Apple accessories or 12-24 V ACDC power source. Wall-mount ready. Power adapter or USB cable NOT included. Jumper wires NOT included. Do NOT power with 110 V Do NOT apply Voltage to the input switch terminals. RELIABLE Z-WAVE Comes with the latest S2 security and a powerful Z-Wave Plus signal repeater to boost your network. Remembers and restores onoff status after power failure. Built-in auto-on and auto-off timer available if your hub supports advanced settings. The device is ETL certified and conforms with North American safety standards.. HUB COMPATIBILITY This is an advanced Z-Wave device and it requires an open Z-Wave hub to display correctly. It was tested to work well with Hubitat, Vera, openHAB, and on SmartThings with a custom device handler please go to Zooz support page for details. ADT Pulse, Vivint, Wink, and Ring all offer partial control one relay or all at once instead of individual control for the relays..

READ BEFORE YOU BUY The Z-Wave stick is for advanced users only, NOT for beginners. You must be comfortable with programming and have expert computer and Z-Wave knowledge to use this device. NVM back-up from 500 or 700 series Z-Wave sticks will brick the device. Do NOT apply NVM backups or firmware updates published outside of the Zooz support portal to avoid bricking the stick and voiding its warranty.. NEW 800 SERIES Z-WAVE LONG RANGE Take advantage of the latest wireless innovation with Z-Wave Long Range that extends your network coverage up to a mile. NOTE Your home automation software needs to support the Long Range implementation on the interface side as well as the end Z-Wave device you add to the network for the Long Range functionality to be fully unlocked.. WHAT YOU NEED This 800 Series Long Range Stick adds Z-Wave Plus and Z-Wave Long Range capability to your DIY smart home set-up. You'll need a dedicated computer PC, laptop, or Raspberry Pi, sold separately and home automation software of your choice not included to complete the system.. ADVANCED Z-WAVE Works great with the most popular software like Home Assitant with JS and HomeSeer. Supports OTA firmware updates and and all of the latest Z-Wave library commands..

HOW IT WORKS You'll need a 12 or 24 V DC not AC power supply depending on your LED strip requirements to power both the strip sold separately and the RGBW Dimmer. Do NOT exceed 120 W total for 12 V DC strips or 240 W total for 24 V DC strips Do NOT use with addressable LED strips. Add the RGBW Dimmer to your Z-Wave hub to get wireless control of your lighting. Program schedules, and create custom scenes if this functionality is supported by your hub.. EXTRAS Enjoy more smart features like energy monitoring, scene control double tap, and SmartStart your hub needs to support these features. Add physical control of the light by connecting an onoff or momentary wall switch to the RGBW Dimmer, the Zooz ZAC99 model will work great. You can also use the 4 input terminals to monitor analog low voltage sensors and add Z-Wave to even more devices around you. RELIABLE TECH The RGBW Dimmer is Z-Wave Plus certified and comes with the latest S2 security protocol as well as 128-bit signal encryption to keep your smart home secure. The device is UL listed and conforms with North American safety standards. Made in Europe with carefully selected components.. HUB COMPATIBILITY This is an advanced Z-Wave device and it requires an open Z-Wave hub to display correctly. It was tested to work well with HomeSeer, Fibaro Home Center, and on SmartThings with a custom device handler please contact seller for details or go to Zooz support page for details. Questions Get in touch with Zooz support or the Amazon seller for quick and friendly help.

4 SMART SENSORS IN 1 This compact device detects and reports motion, temperature, humidity, and light level to your smart home app. Compatible Z-Wave hub required, sold separately.. NEW IMPROVED VERSION The included CR123A battery makes the sensor lasts much longer than the previous version. Updated motion detection allows you to get even quicker activity reports.. CUSTOMIZE IT Choose from 7 levels of motion sensitivity, adjust the motion re-trigger interval, and pick from 4 different LED indicator modes your hub needs to support advanced parameter input.. SECURITY FIRST This sensor is equipped with bank-grade AES signal encryption. It's Z-Wave Plus certified to ensure it complies with the highest industry standards.. WILL IT WORK WITH MY HUB This sensor is NOT supported by Wink, Vivint, ADT Pulse, Qolsys, or other Z-Wave alarm panels. It will work great with open systems like Almond Securify, HomeSeer, Home Assistant, Hubitat, SmartThings Hub with custom device handler contact seller for instructions, VeraEdge, VeraLite running under UI7, and VeraPlus..

SMART FLOOD PREVENTION Shut your main water valve automatically when a leak is detected to prevent costly water damage. The Titan actuator installs over your ball valve and comes with a plug-in leak detector to monitor water presence around it. It will work offline with the probe connected directly to the Titan but the device works best when included to a compatible Z-Wave hub sold separately for full wireless functionality.. EXTREMELY STRONG Unlike other retrofit solutions, the Titan is equipped with a powerful motor that opens and closes even the most stubborn valve reliably. It calibrates on each individual valve once installed for optimal performance.. DIY INSTALLATION You don't need any tools and it takes just a few minutes to mount and calibrate the device. You can use it outdoors too Follow the steps in the manual and installation video carefully when installing the product. Check your set-up before buying suitable for 0.5 - 1.25 ball valves only 3 clearance from the valve center to each side on the pipe, at least 1.25 clearance between the valve handle and the pipe, at least 1 clearance between the pipe and the wall.. Z-WAVE COMPATIBLE Get the most of your Titan Valve Actuator when you include it to your Z-Wave hub. Program it to shut the water off if water is detected on any of your wireless leak sensors sold separately for complete protection. The Titan is compatible with SmartThings, Hubitat, Ring Alarm partial integration only, displays temperature and onoff capability instead of openclose, and Home Assistant. Check with Zooz for compatibility before buying if your hub is not listed.. NEW 700 SERIES This product is built on the latest 700 series Z-Wave chip for better signal coverage than ever and faster communication. Equipped with S2 Security and SmartStart. 5-year manufacturer warranty and lifetime tech support included..

2 SMART OUTPUTS Control 2 dry contact relays independently with one Z-Wave device. Choose from normally closed 10 A and normally open 20 A relays to automate almost any electrical device. Connect an optional wall switch for physical onoff control or use your Z-Wave hub required, sold separately for wireless control. Your smart speaker is NOT a Z-Wave hub. This product is NOT supported by Wink or Z-Wave alarm panels.. 2 SMART INPUTS Monitor 12-24 V or dry contact inputs separately from the dry contact outputs. Connect analog binary sensors to receive status updates in your Z-Wave hub from a connected door sensor, water sensor, HVAC system, or alarm panel. Use the inputs to trigger the outputs automatically.. AUTOMATE ANYTHING Add Z-Wave connectivity to up down DC motors in screens, motorized blinds, or awnings. Perfect to automate your garage door opener use a single ZEN17 to control up to 2 garage doors independently, commercial gates, gas fireplace, sprinklers, doorbell, outdoor lighting, pool pump, whole house fan, and any 1-240 V device up to 20 A.. QUICK INSTALLATION Power it with a 12-24 V ACDC power source or a standard USB C cable included and a power supply sold separately. Wall-mount ready. Jumper wires NOT included. Do NOT power with 110 V. NEW 700 Z-WAVE Enjoy better signal coverage and a stronger Z-Wave repeater for your mesh network with the latest 700 series chip. It comes with S2 authenticated security and SmartStart for easy pairing. Remembers and restores onoff status after power failure. Built-in auto-on and auto-off timer available if your hub supports advanced settings. The device is ETL certified and conforms with North American safety standards..